This article proposes a fully integrated single-channel bistatic frequency-modulated continuous-wave (FMCW) radar transceiver (TRX) that operates at a center frequency of 256 GHz. The main focus of this work is to realize a wideband and efficient radar TRX that offers high resolution of target detection in the short-range FMCW radar sensing application. The radar TRX chip is designed and manufactured using the 130 nm silicon – germanium (SiGe) bipolar complementary metal-oxide-semiconductor (BiCMOS) technology which offers heterojunction bipolar transistors (HBTs) with $f_\mathbf{T}/f_\mathbf{MAX}$ of 300/500 GHz. The transmitter (TX) of the radar TRX is based on a fundamentally operated multiplier-by-8 chain architecture that offers a 3-dB bandwidth of around 65 GHz with a saturated output power of -5.4 dBm. On the other hand, the receiver (RX) is based on a subharmonic architecture that provides a conversion gain (CG) of 10.4 dB with an average noise figure (NF) of 23.5 dB. This TRX is realized with two integrated on-chip folded dipole antennas. The antenna offers high antenna gain and radiation efficiency due to the use of the selective localized backside etching (LBE) technique. This chip consumes 305 mW of power from a 3.3-V supply and occupies a silicon area of 3.3 mm $^2$ . The radar range measurement is performed in an anechoic chamber, and it shows the maximum dynamic range (DR) of around 34 dB at 1-m range of the target.
This paper describes a differential microstrip patch antenna array and a rectangular waveguide to coupled differential microstrip line transition operating at 122 GHz. The antenna array is realized in series-fed topology/architecture and is very suitable for MIMO radar applications. This on-board antenna provides a high antenna gain and radiation efficiency at millimeter-wave frequencies. The rectangular waveguide transition with low insertion loss offers the facilities to characterize the on-board antenna and can also be utilized in a radar system in combination with a horn antenna. The measured bandwidth of the antenna array is 7 GHz with a maximum gain of 12.98 dBi at 122 GHz. The waveguide transition has a bandwidth of 20 GHz at 10-dB return loss. Radar measurements were performed using radar sensors that were equipped with the developed antenna array as well as the waveguide transition in combination with horn antenna for comparison purposes. The radar measurement results with on-board antenna array show a good performance for detecting the range of the target.
This paper presents a differential microstrip patch antenna array that operates at 122 GHz and is suitable for radar applications. The differential line was chosen in the proposed antenna due to the differential radar transceiver. The microstrip patch antenna array was designed to achieve a higher gain and bandwidth compared to a single element antenna. An 8-element series-fed array was designed, fabricated and measured. The 8-element array provides an impedance bandwidth of 14 GHz and a gain of around 13.74dBi at 122 GHz. These measurement results are also in good agreement with the simulation results.
14 June 2024 in IEEE Microwave and Wireless Technology Letters
This letter presents a power amplifier (PA) with excellent power-added efficiency (PAE) for millimeter-wave (mm-wave) applications. The high efficiency is achieved by leveraging a local backside etching (LBE) process to enhance the quality factor ( Q ) of the output matching network. The PA was fabricated in a mature SiGe BiCMOS technology featuring heterojunction bipolar transistors (HBTs) having an $ {f}_{{T}} $ / $ {f}_{\text{max}} $ of 250/340 GHz. While the measured peak PAE is 56% at 24 and 25 GHz, the PA provides 16 dB of peak gain and a 3-dB bandwidth of 19 GHz ranging from 13.5 to 32.5 GHz, which makes the circuit well suited for multiple purposes, such as sensors, radars, 5G, and satellite communications. The maximum PAE exceeds 40% from 22 to 28 GHz, with a peak saturated power ( $ {P}_{\text{sat}} $ ) of 16.5 dBm at 25 GHz. To the best of authors’ knowledge, this PA achieves the highest PAE reported to date for silicon-based mm-wave amplifiers.
This paper proposes a compact and efficient frequency quadrupler (FQ) intended for a sub-harmonic transceiver. The circuit is based on stacked double bootstrapped Gilbert cell (GC) and works at the frequency band of 110-150GHz. It consists of two stacked mixing stages. The GC stages individually perform as a doubler for the input frequency, and the resultant quadrupled signal appears at the output of the second GC stage. The FQ achieves the peak conversion gain of 6.6dB and the maximum output power of -1dBm. The 3-dB bandwidth of this FQ is 40GHz(110-150GHz). Due to the compact design without compromising the performance, the stand-alone FQ Chip occupies only $0.056\text{mm}^{2}$ chip area and consumes only 13.4mA of current from the 3.3V supply. It achieves the maximum drain efficiency of 1.81%. The presented FQ is suitable for the frequency generation circuit in various system design applications above 100GHz.