26 October 2018 in IEEE Transactions on Industrial Electronics
This paper presents two novel consequent-pole permanent magnet (PM) (CPM) machines which featuring N-iron-N-iron-N-S-iron-S-iron-S and iron-S-iron-S-iron-iron-N-iron-N-iron sequences. Furthermore, the tangential PMs are embedded into the proposed CPM machines, and thus enhance output torque and reduce the torque ripple. The principle of the elimination of unipolar leakage flux and the performance improvement by hybrid-pole are analyzed based on the simplified PM magnetic circuit. Then, the rotors of proposed CPM and HPM machines are optimized by finite element analyses. Furthermore, the electromagnetic performances of the proposed machines, including the open-circuit airgap flux density, average torque, torque ripple, loss, efficiency, unbalanced magnetic force, demagnetization withstand capability and unipolar leakage flux, are compared with the conventional SPM and CPM machines. It is demonstrated that both the conventional CPM and proposed HPM machines have >20% higher utilization ratio of PM material than the SPM machine. The proposed HPM machine can obtain almost equivalent torque and efficiency when compared to the conventional CPM machine. Moreover, unipolar leakage flux does not exists in the end shaft of the proposed machines, and thus the magnetization of the mechanical components can be effectively eliminated. Finally, a 9-slot/10-pole HPM machine is prototyped and measured to validate the analyses.
1 May 2018 in IEEE Transactions on Energy Conversion
This paper presents a consequent-pole permanent-magnet (CPM) machine to reduce the volume of permanent magnets (PM) and eliminate the retaining sleeve. The average torque and efficiency can be improved due to the reduced airgap reluctance. The proposed configuration uses dovetail consequent-pole to protect quasi-trapezoidal PMs with lower total rotor loss than conventional surface-mounted PM (SPM) machine due to the half number of PMs and the removed sleeve loss. In addition, the stress and deformation of the rotor are investigated. The electromagnetic performance including back-EMF, average torque, torque ripple, loss, efficiency, unbalanced magnetic force (UMF), demagnetization withstand capability of the proposed CPM machine are investigated by finite element analyses. It is demonstrated that the output torque of the CPM machine can be enhanced by 3% while the PM volume is reduced approximately by 20% compared to that of the conventional SPM machine. Simultaneously, the CPM machine can have lower total harmonic distortions of phase back-EMF, lower torque ripple and higher efficiency than the SPM machine. Finally, the 12-slot/10-pole CPM machine is prototyped to validate the analyses.
7 March 2018 in IEEE Transactions on Energy Conversion
This paper analytically derives the optimal 3rd harmonic current to improve the output torque in five-phase surface-mounted permanent magnet (SPM) machines under the constraints of the same peak/rms value. The relationship between the output torque and the 3rd harmonic current is established and its optimal value for maximizing the output torque is derived. It is found that the optimal 3rd harmonic current is dependent on the ratio of the third harmonic back-EMF to the fundamental one but it is not 1/6 of the fundamental one as pulse width modulation in inverter. In order to improve the output torque by increasing the fundamental and third harmonic winding factors, and the third harmonic airgap flux density, the unequal width tooth and permanent magnet (PM) segmentation are employed in the 10-slot/8-pole five-phase SPM machine. The optimal unequal tooth dimensions and the number of PM segmentations are analyzed for maximizing the output torque. The airgap flux density, back-EMF, cogging torque and output torque of the machine with equal/unequal tooth width and unsegmented/segmented PM are compared. Finally, the experiments on the prototype 10-slot/8-pole PM machine with unequal tooth width and segmented rotor are given to verify the analytical and FE analyses.
19 January 2023 in IEEE Transactions on Power Electronics
The output torque capability of a dual-three-phase permanent magnet synchronous machine (DTP-PMSM) can be increased by intentionally injecting proper harmonic currents, which can be beneficial in some applications that require high torque density. To achieve this, current references containing multiple harmonic components with time-varying frequencies must be accurately tracked by the current controllers, which can hardly be achieved by conventional control methods. Fortunately, to track these complex but predetermined current references, generalized predictive control (GPC) shows unique advantages for its characteristics of multistep prediction and receding horizon optimization. In this article, a current control strategy based on GPC is proposed for the DTP-PMSM, which enhances the output torque capability by tracking the harmonic current references with high accuracy in both phase and magnitude. Parameter tuning and model mismatch issues of the proposed GPC are discussed. The effectiveness and merits of the proposed control strategy are validated by a comparison study based on simulation and experiments.
10 September 2018 in IEEE Transactions on Energy Conversion
This paper presents a consequent-pole permanent magnet (PM) (CPM) machine featuring novel N-S-iron sequences. In order to enhance the output torque and efficiency, the flux barrier is employed, and the tangential magnetized PMs are embedded in the flux barriers to form the hybrid-pole PM (HPM) machine. The rotors of the proposed CPM and HPM machines, as well as its conventional counterpart which employs N-iron sequences, are optimized by finite element (FE) analysis. Furthermore, the electromagnetic performances of the proposed machines, including the open-circuit airgap flux density, back-EMF, average torque, torque ripple, efficiency, flux-weakening capability, unbalanced magnetic force (UMF) and unipolar leakage flux, are compared with the conventional CPM machine. It is demonstrated that the proposed HPM machine can obtain almost equivalent torque, efficiency and better flux-weakening capability compared to the conventional one. Moreover, the proposed HPM machine has no unipolar leakage flux in the end region, and thus the magnetization of the mechanical components can be effectively reduced. Finally, a 9-slot/8-pole HPM machine is prototyped and measured to validate the analyses.
18 March 2020 in IEEE Transactions on Energy Conversion
The static excitation part of a brushless wound rotor hybrid excitation generator without an exciter (brushless WRHEG) is analyzed in this paper. The DC stator excitation windings and rotor harmonic coils are placed in the iron core as the excitation part, so that the brushless excitation for a wound rotor hybrid excitation generator (WRHEG) can be realized. In this study, the selection of stator excitation windings and rotor harmonic coils, which are essential for achieving of the brushless excitation, is providing. The effect of the static magnetic field on the air-gap magnetic field is studied theoretically. The harmonic content of the air-gap magnetic field is analyzed by Fourier series form and the effect of harmonics on the output voltage is also investigated. The influence of the static excitation field on the iron loss is also considered. A 1.5kVA prototype is fabricated to verify the validity of the theoretical and Finite Element (FE) analysis. The output voltage under the no-load and the rated load conditions are measured. The field regulation capacity and the efficiency of the brushless WRHEG are tested. It shows that the brushless excitation is achieved by remaining the operating performance of WRHEG unchanged.