13 April 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
In this paper, a reconfigurable filter is proposed for simultaneous usage as ultra-wideband and wideband filters. The ultra-wideband (UWB) section is designed by constructing three parallelly connected quarter-wavelength transmission lines with two high impedance quarter-wavelength shorted stubs. The wideband (WB) section is implemented using an open stepped impedance stub-loaded resonator (OSSLR) and a shorted stepped impedance stub-loaded resonator (SSSLR). Nine pin diodes are embedded to switch the passband from UWB to WB and vice versa configuration. The filter in UWB mode produces a passband bandwidth (|S11| dB more than 10 dB) of 9.03 GHz from 2.15 GHz to 11.18 GHz, and the WB mode reports a passband bandwidth of 2.8 GHz, which ranges from 3.25 GHz to 6.05 GHz. Further, a lowpass filter is integrated with the design to obtain a wide upper stopband. The proposed prototype is fabricated and tested to validate the collaborative design concept. The overall circuit size of the prototype is 0.80λg × 0.42λg at 4.70 GHz.
1 January 2015 in Progress in Electromagnetics Research C
SCSekhar Ranjan Bhadra Chaudhuri
Sekhar Ranjan Bhadra Chaudhuri
29 December 2020 in IEEE Transactions on Circuits and Systems II: Express Briefs
A dual-functional reconfigurable filter is explored for the application in wideband and triple band band pass filter. The wideband configuration is implemented by parallel combination of open stub loaded and short circuited stub loaded resonators to exhibit a passband from 2.0 GHz-6.1 GHz. Tight coupling generates transmission zeroes at the either side of passband, which enhances the selectivity. The proposed tri-band BPF offers passbands at 2.4 GHz, 3.5 GHz and 5.2 GHz where two-stepped impedance resonators (SIRs) and one uniform impedance resonator (UIR) are assembled to accomplish such behavior. The two short circuited stubs are connected to the feed line to extend the range of upper stopband. PIN diodes are effectively utilized to switch the operation from wideband to tri-band or vice versa. Detailed design guidelines are provided to design the proposed filter. The behavior of the proposed filter topology is investigated by even and odd mode analysis. The developed reconfigurable filter is fabricated and measured to verify the anticipated and simulated results. A close agreement is observed between them. The fabricated reconfigurable BPF has a very compact size, high selectivity, less insertion loss and good return loss profile.
12 October 2020 in Defence Science Journal
In this paper, the potentials of using Global Navigation Satellite System (GNSS) techniques in the complex calibration procedure of the tracking sensors for missile test range applications have been presented. The frequently used tracking sensors in test range applications are- electro-optical tracking stations (EOTS) and tracking radars. Over the years, the EOTS are used as the reference for bias estimation of the radars. With the introduction of GPS in test range applications, especially the DGPS, the reference for bias estimation got shifted to DGPS from the EOTS. However, the achievable position solution accuracy is limited to the order of a few meters for DGPS, EOTS, and Radars. With the evolution of Multi-constellation GNSS and carrier-phase based measurement techniques in satellite navigation, achievable position solution accuracies may be improved to sub-meter level. New navigation techniques like real time kinematic (RTK) and precise point positioning have the potentials for use in the calibration procedures of the missile test ranges to the accuracies of centimeter-level. Moreover, because of the availability of a large number of navigation signals over the Indian region, multi-constellation GNSS receivers can enhance signal availability, reliability, and accuracies during the calibration of missile test ranges. Currently available compact, low-cost GNSS modules also offer the possibilities of using these for cost-effective, networked RTK for dynamic calibration of test ranges reducing cost and resource requirements.
22 July 2013 in Journal of Electromagnetic Waves and Applications
A printed dual band notched ultra wideband monopole antenna with a single perturbed Hilbert curve slot is presented which exhibits 121% impedance bandwidth. A single modified Hilbert curve slot provides dual band notch characteristics in the range of 3.3–3.7 GHz (WiMAX), 3.7–4.2 GHz (C-Band), and 5.15–5.825 GHz (WLAN) which makes the notch design process simpler than other dual band notched antennas. The gain of the proposed antenna varies from 3 to 4 dBi over its operating frequency range, except at the rejection bands. Suitable radiation characteristics are obtained throughout its operating band. Simulation and measured results of the proposed antenna are in good agreement.
1 January 2012 in Progress in Electromagnetics Research C