Giulio Maistro

Giulio Maistro

Auto-generated profile, based on publicly available information

Giulio Maistro

Uddeholms AB, 683 85 Hagfors, Sweden

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2017 in Surface and Coatings Technology
Verified
Journal Article
Closed access
GMG. Maistro
G. Maistro
COC. Oikonomou
C. Oikonomou
LRL. Rogström
L. Rogström
Lars NyborgLars Nyborg
Lars Nyborg
YCY. Cao
Y. Cao

1 April 2017 in Surface Engineering
Verified
Journal Article
Closed access
GMG. Maistro
G. Maistro
Sergio Alfonso Pérez-GarcíaSergio Alfonso Pérez-García
Sergio Alfonso Pérez-García
MNM. Norell
M. Norell
Lars NyborgLars Nyborg
Lars Nyborg
YCYu Cao
Yu Cao
In this study, expanded austenite was prepared by an industrial low-temperature plasma nitriding process in 304L and 904L austenitic stainless steels. The current investigation focuses on the assessment of the thermal stability and related phase evolution of the expanded austenite layer during isothermal annealing in protective argon atmosphere at temperatures ranging from 450 to 600°C for 24 and 168 h. Characterisation of the original expanded austenite and the decomposed surface layers was performed. Denitriding, inward N-diffusion and Cr-compounds precipitation occurred at different extent, depending on annealing conditions and alloy composition. Expanded austenite in 304L exhibited a near complete eutectoid decomposition after a short annealing time, while 904L showed significantly better thermal stability. A fine dispersion of small CrN precipitates resulting from expanded austenite decomposition at relatively low annealing temperature or short duration could further positively affect the surface hardness of both materials. Precipitate growth reduces hardness at higher annealing temperatures/times.

1 June 2021 in Surfaces and Interfaces
Verified
Journal Article
Closed access
GMGiulio Maistro
Giulio Maistro
SKStefan Kante
Stefan Kante
Lars NyborgLars Nyborg
Lars Nyborg
YCYu Cao
Yu Cao

31 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
CBCarlos Botero
Carlos Botero
Aydın ŞelteAydın Şelte
Aydın Şelte
MRMarkus Ramsperger
Markus Ramsperger
GMGiulio Maistro
Giulio Maistro
AKAndrey Koptyug
Andrey Koptyug
LRLars-Erik Rännar
Lars-Erik Rännar
In this work, a highly alloyed cold work tool steel, Uddeholm Vanadis 4 Extra, was manufactured via the electron beam melting (EBM) technique. The corresponding material microstructure and carbide precipitation behavior as well as the microstructural changes after heat treatment were characterized, and key mechanical properties were investigated. In the as-built condition, the microstructure consists of a discontinuous network of very fine primary Mo- and V-rich carbides dispersed in an auto-tempered martensite matrix together with ≈15% of retained austenite. Adjusted heat treatment procedures allowed optimizing the microstructure by the elimination of Mo-rich carbides and the precipitation of fine and different sized V-rich carbides, along with a decrease in the retained austenite content below 2%. Hardness response, compressive strength, and abrasive wear properties of the EBM-manufactured material are similar or superior to its as-HIP forged counterparts manufactured using traditional powder metallurgy route. In the material as built by EBM, an impact toughness of 16–17 J was achieved. Hot isostatic pressing (HIP) was applied in order to further increase ductility and to investigate its impact upon the microstructure and properties of the material. After HIPing with optimized protocols, the ductility increased over 20 J.

12 August 2024 in Metals
Verified
Journal Article
Open access
PDF file
ANAnok Babu Nagaram
Anok Babu Nagaram
GMGiulio Maistro
Giulio Maistro
EAErik Adolfsson
Erik Adolfsson
YCYu Cao
Yu Cao
Eduard HryhaEduard Hryha
Eduard Hryha
Lars NyborgLars Nyborg
Lars Nyborg
Vanadis 4E (V4E) is a powder metallurgical cold work tool steel predominantly used in application with demand for wear resistance, high hardness, and toughness. It is of interest to have a processing route that enables full density starting from clean gas-atomized powder allowing component shaping capabilities. This study presents a process involving freeze granulation of powder to facilitate compaction by means of cold isostatic pressing, followed by sintering to allow for capsule-free hot isostatic pressing (HIP) and subsequent heat treatments of fully densified specimens. The sintering stage has been studied in particular, and it is shown how sintering in pure nitrogen at 1150 °C results in predominantly closed porosity, while sintering at 1200 °C gives near full density. Microstructural investigation shows that vanadium-rich carbonitride (MX) is formed as a result of the nitrogen uptake during sintering, with coarser appearance for the higher temperature. Nearly complete densification, approximately 7.80 ± 0.01 g/cm3, was achieved after sintering at 1200 °C, and after sintering at 1150 °C, followed by capsule-free HIP, hardening, and tempering. Irrespective of processing once the MX is formed, the nitrogen is locked into this phase and the austenite is stabilised, which means any tempering tends to result in a mixture of austenite and tempered martensite, the former being predominate during the sequential tempering, whereas martensite formation during cooling from austenitization temperatures becomes limited.