5 June 2024 in IEEE Transactions on Microwave Theory and Techniques
This article presents an accurate phase calibration technique and a fast time-domain reconstruction algorithm for frequency-modulated continuous wave (FMCW) synthetic aperture radar (SAR) imaging in 3-D. The phase calibration is tailored toward millimeter-wave imaging systems that operate over a wide bandwidth. The first step in the calibration is to estimate the phase nonlinearities in the chirp signal. This is done by using a two-point relative distance calibration measurement. Range deskewing is used to perform a range independent nonlinearity correction to the measured intermediate frequency (IF) signals. The second step in the calibration is to bring the phase reference to the phase center of the antenna by using a conducting stencil as a reference target. The calibrated IF signal is shown to follow a time-domain dispersion relation that is conducive to fast near-field imaging. Based on this, a holographic time-domain 3-D image reconstruction algorithm is presented. The reconstruction is composed of two 2-D fast-Fourier transforms (FFTs) and a 1-D nonuniform FFT (NUFFT). The proposed algorithm is two orders of magnitude faster than existing time-domain reconstruction algorithms for FMCW 3-D imaging radars. A $W$ -band (76–84 GHz) FMCW system is used to experimentally verify the proposed calibration and reconstruction. The measured lateral resolution is shown to reach the theoretical diffraction limit, demonstrating near-perfect phase reconstruction. Several experiments of 3-D targets and concealed objects are presented to demonstrate the high quality of 3-D images that can be generated from FMCW SAR data. The experimental datasets and codes are available at: https://github.com/AdityaMuppala.
9 June 2023 in IEEE Transactions on Geoscience and Remote Sensing
A mechanically scanned high-resolution 2-D imaging radar system with full 360° Field-of-View (FoV) is presented. The system is composed of a multi-function 222-228 GHz frequency modulated continuous wave (FMCW) radar and a moment of inertia optimized 3-D printed offset reflector antenna. The reflector geometry is made from an Elliptic Toroidal surface which is shown to produce a high-gain fan-beam with an 11:1 aspect ratio. The reflector is rotated at speeds up to 10 Hz for high throughput imaging. The wobble generated by the high speed rotation is suppressed by optimizing the mass distribution of the reflector body. It is fabricated in-house using a low-cost table-top Fused Deposition Modelling (FDM) 3-D printer. The reflecting surface is metallized with a silver coated copper paint and processed using simple steps to ensure smoothness and accuracy. The reflector achieves beamwidths of 4.6° in elevation and 0.42° in azimuth, with a peak gain of 38.7 dBi. The 3 dB azimuthal resolution of the radar two-way beam is measured to be 0.3°. The system is tested in real-world scenarios and the resulting images and videos are of unprecedented quality due to the large area of coverage, high resolution, high speed and excellent dynamic range. To the best of our knowledge, this is the first demonstration of a compact radar system that is comparable in resolution, speed and angular coverage to lidars, while offering higher dynamic range and immunity to severe weather and lighting conditions.
5 November 2018 in IEEE Transactions on Intelligent Transportation Systems
This paper proposes radar sensors operating at J-band (220-320 GHz) for automotive applications. Operating at J-band, at about three times higher frequency than the currently available automotive radars operating at 77 GHz, will result in three-fold improvement in cross-range resolution for the same antenna size. Since the characterization of the radar backscatter from different objects on the traffic scenes is necessary for optimizing the design of automotive sensors, the work reported in this paper is the start of a broader study that attempts to fill the lack of knowledge on radar backscatter behavior of road environment at this frequency band. Considering vehicles as the most important object for automotive radars, this paper investigates the response of vehicles from different aspects. A combination of outdoor high-resolution synthetic aperture radar imaging experiments and real-aperture imaging measurements of vehicles are performed using a 222-GHz polarimetric instrumentation radar. The aim of these experiments is to identify the scattering centers on different vehicle bodies and to determine the statistics of the radar return. The results show that significant scattering is due to a limited number of fixtures on the vehicle's outer surfaces facing the radar. The strongest scattering phase-centers observed are due to specular reflections and, hence, have a strong dependence on the relative look angle. The statistics associated with backscatter from vehicles are found, in most cases, to best fit the Weibull distribution.
5 August 2021 in IEEE Transactions on Instrumentation and Measurement
A broadband (1–35 GHz) time-/frequency-domain reflection technique for measuring the complex dielectric constant of low-loss dielectric slabs is presented. The technique uses a coplanar waveguide (CPW) transmission line sample holder for measurements. In addition to the standard substrate materials, the technique is suitable for the characterization of materials, such as glass, as it does not require complicated sample machining and preparation. The procedure is based on comparing the measured effective dielectric constant and the attenuation constants for both the loaded and unloaded CPW line sample holder. The effective dielectric constant and the attenuation constant are first modeled as a function of the real and imaginary parts of the superstrate’s dielectric constant using a 2-D numerical line calculator. Samples under test are assumed to be nonmagnetic and have their material resonances at frequencies substantially above 35 GHz. The technique is validated through measurements of known Rogers RT/duroid samples. Measured complex dielectric constants of different materials are in very good agreement with data reported in materials’ datasheets.
10 June 2021 in IEEE Transactions on Terahertz Science and Technology
An antenna system is proposed that uses a novel polarization-independent spatial power divider to align the beams from two orthogonally oriented dual-polarized feeds. This antenna system uses a common aperture for transmitting and receiving and provides high port isolation while maintaining compatibility with fully polarimetric radar. Unlike conventional two antenna radar systems, a radar using this antenna does not suffer from the parallax problem. The spatial power divider is designed using an all-dielectric metasurface approach and is fabricated on a silicon wafer using standard micromachining technology. The measured device exhibits at most 0.9 dB of difference between the reflection and transmission for both transverse electric and transverse magnetic incident waves at 45° incidence, over a band from 221 to 250 GHz. Conical horns are fabricated as feeds and together with the spatial power divider, a focusing lens, and microwave absorbers, are assembled in a three-dimensional-printed housing to complete the antenna system. Its measured gain is approximately 39 dB for each port and polarization, and isolation between ports is at least 40 dB for all polarization combinations over the band of interest.
20 December 2021 in IEEE Transactions on Geoscience and Remote Sensing
This article presents a comprehensive technique for calibrating wideband frequency-modulated continuous-wave (FMCW) fully polarimetric radars employing linear FM (LFM) signal chirps. A detailed system distortion model is developed that accounts for both polarimetric distortions and distortions caused by nonlinearities in the transmitted and received radar chirps over multiple polarization channels. Using the radar responses of two point targets at known distances from the radar, the calibration technique is able to estimate the range-dependent nonlinearities in phase and correct them for all targets at all ranges. This allows the radar to achieve its ideal range resolution. In addition, the calibration technique corrects for channel imbalances in the polarimetric radar using a metallic sphere of known diameter and any depolarizing target. Both numeric simulations and actual polarimetric radar measurements using a wideband FMCW radar operating over 76.5–82 GHz were used to validate the calibration technique.