Herein, we report an atomic layer deposition (ALD) process for Cu2O thin films using copper(II) acetate [Cu(OAc)2] and water vapor as precursors. This precursor combination enables the deposition of phase-pure, polycrystalline, and impurity-free Cu2O thin films at temperatures of 180–220 °C. The deposition of Cu(I) oxide films from a Cu(II) precursor without the use of a reducing agent is explained by the thermally induced reduction of Cu(OAc)2 to the volatile copper(I) acetate, CuOAc. In addition to the optimization of ALD process parameters and characterization of film properties, we studied the Cu2O films in the fabrication of photoconductor devices. Our proof-of-concept devices show that approximately 20 nm thick Cu2O films can be used for photodetection in the visible wavelength range and that the thin film photoconductors exhibit improved device characteristics in comparison to bulk Cu2O crystals.
1 January 2022 in Review of Scientific Instruments
An ambient pressure cell is described for conducting synchrotron-based x-ray photoelectron spectroscopy (XPS) measurements during atomic layer deposition (ALD) processes. The instrument is capable of true in situ and operando experiments in which it is possible to directly obtain elemental and chemical information from the sample surface using XPS as the deposition process is ongoing. The setup is based on the ambient pressure XPS technique, in which sample environments with high pressure (several mbar) can be created without compromising the ultrahigh vacuum requirements needed for the operation of the spectrometer and the synchrotron beamline. The setup is intended for chemical characterization of the surface intermediates during the initial stages of the deposition processes. The SPECIES beamline and the ALD cell provide a unique experimental platform for obtaining new information on the surface chemistry during ALD half-cycles at high temporal resolution. Such information is valuable for understanding the ALD reaction mechanisms and crucial in further developing and improving ALD processes. We demonstrate the capabilities of the setup by studying the deposition of TiO2 on a SiO2 surface by using titanium(IV) tetraisopropoxide and water as precursors. Multiple core levels and the valence band of the substrate surface were followed during the film deposition using ambient pressure XPS.
In this work, we developed an atomic layer deposition (ALD) process for gold metal thin films from chloro(triethylphosphine)gold(I) [AuCl(PEt3)] and 1,4-bis(trimethylgermyl)-1,4-dihydropyrazine [(Me3Ge)2DHP]. High purity gold films were deposited on different substrate materials at 180 °C for the first time with thermal reductive ALD. The growth rate is 1.7 Å/cycle after the film reaches full coverage. The films have a very low resistivity close to the bulk value, and a minimal amount of impurities could be detected. The reaction mechanism of the process is studied in situ with a quartz crystal microbalance and a quadrupole mass spectrometer.
3 June 2019 in The Journal of Physical Chemistry C
LiMn2O4 is a promising candidate for a cathode material in lithium ion batteries (LIBs) due to its ability to intercalate lithium ions reversibly through its three-dimensional manganese oxide network. One of the promising techniques for depositing LiMn2O4 thin film cathodes is atomic layer deposition (ALD). Due to its unparalleled film thickness control and film conformality, ALD helps to fulfill the industry demands for smaller devices, nanostructured electrodes and all-solid-state batteries. In this work the intercalation mechanism of Li+ ions into an ALD grown β-MnO2 thin film was studied. Samples were prepared by pulsing LiOtBu and H2O for different cycle numbers onto about 100 nm thick MnO2 films at 225 ºC and characterized with X-ray absorption spectroscopy (XAS), X-ray diffraction (XRD), X-ray reflectivity (XRR), time-of-flight elastic recoil detection analysis (TOF-ERDA) and residual stress measurements. It is proposed that for < 100 cycles of LiOtBu/H2O the Li+ ions penetrate only to the surface region of the β-MnO2 film and the samples form a mixture of β-MnO2 and a lithium deficient non-stoichiometric spinel phase LixMn2O4 (0 < x < 0.5). When the lithium concentration exceeds x ≈ 0.5 in LixMn2O4 (corresponding to 100 cycles of LiOtBu/H2O), the crystalline phase of manganese oxide changes from the tetragonal pyrolusite to the cubic spinel, which enables Li+ ions to migrate throughout the whole film. Annealing in N2 at 600 ºC after the lithium incorporation seemed to convert the films completely to the pure cubic spinel LiMn2O4.
1 February 2023 in Journal of Vacuum Science & Technology A
In this paper, we introduce a vacuum cluster tool designed specifically for studying reaction mechanisms in atomic layer deposition (ALD) and atomic layer etching (ALE) processes. In the tool, a commercial flow-type ALD reactor is in vacuo connected to a set of UHV chambers so that versatile surface characterization is possible without breaking the vacuum environment. This way the surface composition and reaction intermediates formed during the precursor or etchant pulses can be studied in very close to true ALD and ALE processing conditions. Measurements done at each step of the deposition or etching cycle add important insights about the overall reaction mechanisms. Herein, we describe the tool and its working principles in detail and verify the equipment by presenting results on the well-known trimethyl aluminum–water process for depositing Al2O3.