Alonso Herman Ricci Castro

Alonso Herman Ricci Castro

Auto-generated profile, based on publicly available information

Alonso Herman Ricci Castro

Centro de Ciência e Tecnologia de Plasmas e Materiais—PlasMat, Instituto Tecnológico de Aeronáutica, Praça Marechal Eduardo Gomes 50, 12228-900, São José dos Campos, SP, Brazil

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2014 in Applied Surface Science
Verified
Journal Article
Open access
KKKonstantin Georgiev Kostov
Konstantin Georgiev Kostov
TNThaita Nishime
Thaita Nishime
ACA.H.R. Castro
A.H.R. Castro
ATA. Toth
A. Toth
LHL.R.O. Hein
L.R.O. Hein
In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40 degrees in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure. (C) 2014 Elsevier B.V. All rights reserved

1 February 2017 in Surface and Coatings Technology
Verified
Journal Article
Closed access
ACAlonso H. Ricci Castro
Alonso H. Ricci Castro
FKFelipe Vicente de Paula Kodaira
Felipe Vicente de Paula Kodaira
VPVadym Prysiazhnyi
Vadym Prysiazhnyi
RMRogerio P. Mota
Rogerio P. Mota
KKKonstantin Georgiev Kostov
Konstantin Georgiev Kostov

13 December 2016 in Brazilian Journal of Physics
Verified
Journal Article
Closed access
PDF file
VPVadym Prysiazhnyi
Vadym Prysiazhnyi
ACAlonso H. Ricci Castro
Alonso H. Ricci Castro
KKKonstantin Georgiev Kostov
Konstantin Georgiev Kostov

22 November 2018 in Plasma Research Express
Verified
Journal Article
Closed access
PDF file
ADA C O C Doria
A C O C Doria
FFF R Figueira
F R Figueira
JLJ S B de Lima
J S B de Lima
JFJ A N Figueira
J A N Figueira
ACA H R Castro
A H R Castro
Rodrigo PessoaRodrigo Pessoa
Rodrigo Pessoa
Candida spp are present in 70%–90% of invasive infections and non-thermal plasmas operated at atmospheric pressure have been gaining attention as a new antimicrobial strategy for medical devices. This work presents studies on the inactivation efficacy of biofilms of Candida albicans grown in polyurethane (PU), main constituent of central venous catheter, by atmospheric gliding arc plasma jet operated at different process parameters: gas chemistry/flow (argon, helium, or its mixture with air) and plasma pulsing. The investigation was performed in the post-discharge region of the plasma jet. After plasma treatment, the colony-forming units (CFU) were counted, and the chemical bonding (FT-IR) and morphological (SEM) analyses of the surface of the biofilm plus PU substrate were investigated. Furthermore, optical emission spectroscopy (OES) technique was applied to characterize the plasma chemistry and measure the OH concentration and rotational temperature, together with thermal analyses of the substrate during treatment. CFU results showed that gliding arc plasma jet was efficient for the inactivation of C. albicans biofilms. It obtained a maximum CFU reduction of 100% and 98% for 4 L min −1 air/6 L min −1 He and 99% and 98% for 4 L min −1 air/6 L min −1 Ar in continuous and pulsed mode, respectively. SEM and FT-IR analyses corroborate with results of % CFU reduction, showing a reduction of the biofilm constituents on the substrate surface. From OES and substrate thermal analyses, it was possible to verify that, although the OH concentration and rotational temperature of air/He plasma jet are lower in comparison to the air/Ar, a drastic increase of the substrate temperature during the treatment (up to 70 °C) was observed for this plasma chemistry.

1 February 2017 in Surface and Coatings Technology
Verified
Journal Article
Closed access
FKFelipe Vicente de Paula Kodaira
Felipe Vicente de Paula Kodaira
ACA.H. Ricci Castro
A.H. Ricci Castro
VPVadym Prysiazhnyi
Vadym Prysiazhnyi
RMR.P. Mota
R.P. Mota
AQA. Quade
A. Quade
KKKonstantin Georgiev Kostov
Konstantin Georgiev Kostov

28 August 2015 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
ACAlonso Herman Ricci Castro
Alonso Herman Ricci Castro
KKKonstantin Georgiev Kostov
Konstantin Georgiev Kostov
VPVadym Prysiazhnyi
Vadym Prysiazhnyi
The influence of nozzle geometry on the properties of atmospheric-pressure Ar plasma jet was investigated. Three different nozzle types were tested: 1) a tapered nozzle (to get a thin plasma plume); 2) a straight nozzle (used in most cases); and 3) an enlarged nozzle (to increase the active plasma area). The electrical properties and visual appearance of the generated plasma were studied with these three nozzles. The jet's performance for surface modification was evaluated by measuring the area of the samples with enhanced wettability and comparing it with the image analysis of the light emission over the sample surface. It has been concluded that limiting the nozzle diameter can be a solution to reduce the treatment area. However, the decrease in the treated area is limited due to the plasma spreading. The use of widen nozzle leads to increase in the treated area and possibility to control the mixture of the carrier gas with ambient air, making this nozzle configuration potentially interesting for other applications, as, for example, treatment of small 3-D objects.