James C. Gallagher

James C. Gallagher

Auto-generated profile, based on publicly available information

James C. Gallagher

U.S. Naval Research Laboratory

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 September 2019 in Applied Physics Express
Verified
Journal Article
Closed access
PDF file
JGJames C. Gallagher
James C. Gallagher
AKAndrew D. Koehler
Andrew D. Koehler
MTMarko J. Tadjer
Marko J. Tadjer
NMNadeem A. Mahadik
Nadeem A. Mahadik
TATravis J. Anderson
Travis J. Anderson
FKFrancis J. Kub
Francis J. Kub

27 July 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
PPPrakash Pandey
Prakash Pandey
TNTolen M. Nelson
Tolen M. Nelson
WCWilliam M. Collings
William M. Collings
MHMichael R. Hontz
Michael R. Hontz
DGDaniel G. Georgiev
Daniel G. Georgiev
Raghav KhannaRaghav Khanna
Raghav Khanna
Vertical power devices require significant attention to their edge termination designs to obtain higher breakdown voltages without substantial increase in ON-state resistance. A simple edge termination structure for a GaN p-n diode is proposed, comprising a full layer lightly doped p-type GaN region underneath the higher doped ${p} +\!+$ contact layer. A TCAD model of the device is developed, and removal of the portions of ${p}$ ++ cap outside of the device active area in simulations is shown to increase the device blocking voltage capability. It causes the depletion width to increase in the lightly doped p-type layer and allows it to act similar to a junction termination extension (JTE). These predictions are validated empirically, resulting in a 52% measured increase in breakdown capability after selective removal of the ${p}$ ++ cap. This simple edge termination technique can be formed with only a single low-energy nitrogen implant or etching procedure, greatly increasing its manufacturability over more complex structures. Design optimization studies are pursued in TCAD to determine optimal parameter values for further improving breakdown performance. It is shown that the proposed edge termination technique can be employed to produce future high voltage vertical GaN devices without a significant gain in ON-state resistance and with wide tolerance to process variations.

13 January 2022 in Scientific Reports
Verified
Journal Article
Open access
PDF file
JGJames C. Gallagher
James C. Gallagher
MEMona A. Ebrish
Mona A. Ebrish
MPMatthew A. Porter
Matthew A. Porter
AJAlan G. Jacobs
Alan G. Jacobs
BGBrendan P. Gunning
Brendan P. Gunning
TATravis J. Anderson
Travis J. Anderson
To improve the manufacturing of vertical GaN devices for power electronics applications, the effects of defects in GaN substrates need to be better understood. Many non-destructive techniques including photoluminescence, Raman spectroscopy and optical profilometry, can be used to detect defects in the substrate and epitaxial layers. Raman spectroscopy was used to identify points of high crystal stress and non-uniform conductivity in a substrate, while optical profilometry was used to identify bumps and pits in a substrate which could cause catastrophic device failures. The effect of the defects was studied using vertical P-i-N diodes with a single zone junction termination extention (JTE) edge termination and isolation, which were formed via nitrogen implantation. Diodes were fabricated on and off of sample abnormalities to study their effects. From electrical measurements, it was discovered that the devices could consistently block voltages over 1000 V (near the theoretical value of the epitaxial layer design), and the forward bias behavior could consistently produce on-resistance below 2 mΩ cm2, which is an excellent value considering DC biasing was used and no substrate thinning was performed. It was found that high crystal stress increased the probability of device failure from 6 to 20%, while an inhomogeneous carrier concentration had little effect on reverse bias behavior, and slightly (~ 3%) increased the on-resistance (Ron). Optical profilometry was able to detect regions of high surface roughness, bumps, and pits; in which, the majority of the defects detected were benign. However a large bump in the termination region of the JTE or a deep pit can induce a low voltage catastrophic failure, and increased crystal stress detected by the Raman correlated to the optical profilometry with associated surface topography.

6 October 2017 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Open access
PDF file
JHJennifer Kristine Hite
Jennifer Kristine Hite
TATravis J. Anderson
Travis J. Anderson
MMM. A. Mastro
M. A. Mastro
LLL. E. Luna
L. E. Luna
JGJ. C. Gallagher
J. C. Gallagher
CEC. R. Eddy
C. R. Eddy
The properties of thick GaN layers grown by metal organic chemical vapor deposition on 2″ HVPE substrates were investigated. Although the epilayer is smooth on a microscopic scale with high quality layers as evidenced by X-ray diffraction and photoluminescence, macroscopic morphological variations are observed on the wafer surface. These variations correspond to disparities in leakage current in fabricated Schottky barrier diodes, with rougher macroscopic morphology resulting in increased leakage current.

24 March 2021 in Journal of Electronic Materials
Verified
Journal Article
Closed access
PDF file
JGJames C. Gallagher
James C. Gallagher
TATravis J. Anderson
Travis J. Anderson
AKAndrew D. Koehler
Andrew D. Koehler
MEMona Ebrish
Mona Ebrish
GFGeoffrey M. Foster
Geoffrey M. Foster
FKFrancis J. Kub
Francis J. Kub

16 September 2017 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Open access
PDF file
JGJ. C. Gallagher
J. C. Gallagher
TAT. J. Anderson
T. J. Anderson
AKA. D. Koehler
A. D. Koehler
NMN. A. Mahadik
N. A. Mahadik
ANA. Nath
A. Nath
FKF. J. Kub
F. J. Kub
In this work, we fabricate Van der Pauw structures on AlGaN/GaN high electron mobility transistors (HEMTs) with both SiN and AlN passivation layers and both SiC and GaN substrates to study temperature dependent electron transport properties of 2 dimensional electron gases (2DEG) in as-fabricated and proton irradiated devices. We confirm that using a GaN substrate or AlN passivation layer enhances the mobility particularly at low temperatures, though this enhancement is greatly reduced upon irradiating the samples with high proton fluences. Our results suggest that the sheet density may be affected by Al diffusion in the sample creating electron donating impurities, which freeze out around 200 K and are more prominent in AlN passivated samples and minimized by using a GaN over a SiC substrate. Additionally, we show that a large dose of radiation forms traps in the AlGaN layer, which drop the sheet density at high proton fluences.