Takeshi Yoshida

Takeshi Yoshida

Auto-generated profile, based on publicly available information

Takeshi Yoshida

Graduate School of Advanced Science and Engineering, Hiroshima University, Higashihiroshima, Hiroshima, JAPAN

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 July 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
SHShinsuke Hara
Shinsuke Hara
RDRuibing Dong
Ruibing Dong
SLSangyeop Lee
Sangyeop Lee
KTKyoya Takano
Kyoya Takano
NTNaoya Toshida
Naoya Toshida
MFMinoru Fujishima
Minoru Fujishima
A 76-Gbit/s 265-GHz CMOS receiver (RX) modularized with a WR-3.4 waveguide interface is presented. It is a mixer-first RX fabricated using a 40-nm CMOS technology. The primary design focus is simplicity and the resulting low noise and loss and high conversion gain (CG). To allow for both on-wafer and packaged measurements, ON-chip transmission lines are designed such that their characteristics are relatively insensitive to the presence or absence of adhesive covering the chip. The RX chip is flip-chip-mounted on a multilayer printed circuit board (PCB). Built into the PCB is a waveguide transition using double-resonant stacked patches for wideband operation. The CMOS RX module achieves the highest wireless data rate of 76 Gbit/s with 16 QAM, which is comparable to 80 Gbit/s reported previously for a CMOS RX with on-wafer probing measurement.

5 May 2025 in IEEE Solid-State Circuits Letters
Verified
Journal Article
Open access
STSatoshi Tanaka
Satoshi Tanaka
SHShinsuke Hara
Shinsuke Hara
KTKyoya Takano
Kyoya Takano
AKAkifumi Kasamatsu
Akifumi Kasamatsu
YSYoshiki Sugimoto
Yoshiki Sugimoto
MFMinoru Fujishima
Minoru Fujishima
This paper presents a near-λ/2-antenna-pitch 2D phased-array CMOS receiver to address the challenge of implementing sub-THz beamforming with the narrow λ/2 (555 μ m at 270 GHz) antenna pitch. A double superheterodyne architecture is adopted to reduce the area occupied by the 2D RX array circuits by locating the E-and H-plane phase control circuits outside the array. Additionally, interpolated feeding is employed to enlarge the area available for the RX circuits by enabling an n-byn array of RX elements to feed a near-λ/2-pitch (2n -1)-by-(2n -1) antenna array composed of main and auxiliary antennas. A 40-nm CMOS prototype with 2×2 RX elements feeding 3×3 antenna elements demonstrate beam scanning ranges of approximately ±20∘ and ±30∘ in the E-and Hplanes, respectively, and achieves 36 Gb/s QPSK signal transmission over a distance of 5 cm.

1 June 2017
Verified
Conference Paper
Closed access
KKK. Katayama
K. Katayama
SAS. Amakawa
S. Amakawa
KTK. Takano
K. Takano
TYT. Yoshida
T. Yoshida
MFMinoru Fujishima
Minoru Fujishima
HTH. Takatsuka
H. Takatsuka
A low-power CMOS W-band amplifier that feeds on a 0.5-V supply is presented. It achieves a peak gain of 24.1 dB and consumes 12mW. This was made possible by (a) the use of Mie Fujitsu Semiconductor 55-nm CMOS technology with deeply depleted channel (DDC) MOSFETs, which are meant specifically for ultralow-power designs with sub-1V supply voltage, (b) high-f max transistor layout, which gives about 1 dB higher gain in the W-band than the ordinary layout, and (c) single-ended negative-capacitance feedback technique, which gives wideband gain boosting comparable to its differential counterpart (with cross-coupled feedback capacitors) with half the power consumption of the latter.

1 October 2022 in IEICE Transactions on Electronics
Verified
Journal Article
Closed access
PDF file
SLSangyeop Lee
Sangyeop Lee
SAShuhei Amakawa
Shuhei Amakawa
TYTakeshi Yoshida
Takeshi Yoshida
MFMinoru Fujishima
Minoru Fujishima
A power-scalable wideband distributed amplifier is proposed. For reducing the power consumption of this power-hungry amplifier, it is efficient to lower the supply voltage. However, there is a hurdle owing to the transistor threshold voltage. In this work, a CMOS deeply depleted channel process is employed to overcome the hurdle.

1 June 2014
Verified
Conference Paper
Open access
SDSi Devices
Si Devices
TMToshihiko Maemoto
Toshihiko Maemoto
YIYasuaki Ishikawa
Yasuaki Ishikawa
TYTakeshi Yoshida
Takeshi Yoshida
Start of the above-titled section of the conference proceedings record.

26 June 2025 in IEEE Access
Verified
Journal Article
Open access
CQChao Qi
Chao Qi
SLSangyeop Lee
Sangyeop Lee
TYTakeshi Yoshida
Takeshi Yoshida
TSTadahiko SHINSHI
Tadahiko SHINSHI
Aterahertz band (e.g., 150 GHz/300 GHz), with its broad bandwidth and potential for improved angular and distance resolution, is attracting attention for Beyond 5G/6G communication and sensing applications (radar, imager, etc.). However, as frequencies increase and wavelengths shorten, mechanical tolerances during integration can significantly impact performance (reflection, transmission, etc.), necessitating effective compensation mechanisms. In this paper, we verify the performance variations caused by mechanical tolerances in transmission-line-to-waveguide transitions, which integrate chips, substrates, and waveguides to transmit signals generated by the chip or receive signals from external sources. To overcome these challenges, a tunable-membrane microactuator is proposed, which adjusts the position of the back-short in the transition by using a flexible conductive membrane and a microactuator (dimension: ϕ10mm×16 mm, maximum stroke of the membrane: 707.7 μm, accuracy<1 μm). The proposed waveguide transition comprises a transmission line and a probe integrated on the multi-layer substrate, along with waveguide flanges and the tunable membrane microactuator. Based on simulation and measurement results, this paper demonstrates the capability of the proposed technology to tune the reflection/transmission losses and frequency bandwidth characteristics of a 249-GHz waveguide transition.