1 October 2009 in Journal of Structural Engineering
Double skin composite walls are composed of two steel plate “skins” connected by tie bars, with the space between them filled with concrete. They were developed to reduce wall thickness, to enhance constructability, and to enable rapid construction by eliminating the use of formwork and reinforcing bars. In the present study, cyclic testing was performed to investigate the seismic behavior of isolated and coupled double skin composite walls with rectangular and T-shaped cross sections. The wall specimens failed mainly by tensile fracture of the welded joints at the wall base and coupling beams, or by local buckling of the steel plates. Because of their large depth, the ductility of the wall specimens was not as good as that of beams having less depth. In particular, the ductility of the walls was significantly affected by the strengthening methods used for the wall base. The load-carrying capacities of the isolated and coupled wall specimens were evaluated using plastic stress distributions in their cross sections, which provided satisfactory predictions.
1 December 2005 in Journal of Structural Engineering
This paper presents test results on eight reduced beam section (RBS) steel moment connections. The testing program addressed web connection type (bolted versus welded) and panel zone (PZ) strength as the key variables. Specimens with medium PZ strength were designed to promote energy dissipation from both PZ and RBS regions such that expensive doubler plates were not needed. Both strong and medium PZ specimens with a welded web connection were able to provide satisfactory connection rotation capacity for special moment-resisting frames. However, specimens with a bolted web connection performed poorly due to premature brittle fracture of the beam flange at the weld access hole. A plausible explanation for the higher incidence of base metal fracture in bolted web specimens was presented based on the measured strain data. Test results from this study and by others showed that panel zones could easily develop a plastic rotation of without causing distress to the beam flange groove welds. At this deformation level, the amount of beam distortion (i.e., buckling) was about one half that developed in strong PZ specimens. A criterion for a balanced PZ strength that improves the plastic rotation capacity while reducing the amount of beam buckling is proposed.
1 June 2013 in Journal of Structural Engineering
Flexural tests on full-scale I-shaped beams, built up from high-strength steels (HSB800 and HSA800) with a nominal tensile strength of 800 MPa, were carried out to study the effect of flange slenderness on flexural strength and rotation capacity. The primary objective was to investigate the appropriateness of extrapolating current stability criteria (originally developed for ordinary steel) to high-strength steel. For comparison purposes, specimens with ordinary steel (SM490) were also tested and showed sufficient flexural strength and rotation capacity in accordance with the AISC specification. The performance of high-strength steel specimens was also very satisfactory from the strength, but not from the rotation capacity, perspective. The inferior rotation capacity of high-strength steel beams was shown to be directly attributable to the absence of a distinct yield plateau and the high yield ratio of the material. When a higher rotation capacity is required as in plastic design, the testing clearly showed that high-strength steel beams were vulnerable to brittle fracture when full-height transverse stiffeners were welded to the tension flange in the plastic hinge region. Residual stress measurements reconfirmed that the magnitude of the residual stress is almost independent of the yield stress of the base metal.
1 August 2017 in Journal of Structural Engineering
In this study, the behavior of high-strength steel circular hollow section (CHS) X-joints was systematically investigated by experimental and test-validated numerical analysis. A total of nine CHS X-joints fabricated from cold-formed tubes were tested under axial compression. The key test variables included different grades of steels and geometrical configuration of the joint. The joint strength observed was mostly governed by the widely accepted 3% indentation criteria before reaching the peak strength. All of the high-strength steel X-joints tested in this study exceeded the nominal strength with sufficient margin found in the Eurocode. Supplemental numerical results also corroborated this experimental observation, implying that the joint strength reduction factor of 0.8, which currently used for high-strength steels in the Eurocode, may be too conservative and needs to be re-examined. Overall, the experimental and supplemental numerical results of this study indicated that high-strength steel CHS X-joints show satisfactory performance, just slightly inferior to ordinary steels, in terms of serviceability, ultimate strength and ductility, even when the yield strength of steel is as high as 800 MPa.
1 February 2010 in Journal of Structural Engineering
In this study, a parallel axial-flexural hinge model capable of representing postyield flexural behavior and considering interaction effects of axial force and moment is proposed for a simplified nonlinear progressive collapse analysis of welded steel moment frames. To this end, the load-resisting mechanism of the column-removed double-span beams was investigated based on the material and geometric nonlinear parametric finite-element analysis. A multilinear parallel point hinge model which captures the moment-axial tension interaction was then proposed. The emphasis was to develop a reliable and computationally efficient macromodel for practical progressive collapse analysis. The application of the proposed hinge model to nonlinear dynamic progressive collapse analysis was illustrated by using OpenSEES program. The accuracy as well as the efficiency of the proposed model was verified based on inelastic dynamic finite-element analysis results. The importance of including catenary action effects for proper ...
1 February 2017 in Journal of Constructional Steel Research