23 February 2021 in IET Renewable Power Generation
This study focuses on a zero voltage transition multi‐input quasi‐Z‐source converter (qZSC). This topology can be used for input sources with different voltages and currents to provide a constant output voltage. In the proposed structure, several qZSCs are combined and the output filter of all stages is eliminated. Therefore, the overall number of circuit elements, cost, volume and weight are reduced in comparison with when they are in a separate operation. In this converter, the soft‐switching conditions are provided for all stages by using only one auxiliary circuit. The employed technique provides zero‐voltage zero‐current switching (ZVZCS) and zero‐voltage switching for main switches at turn‐on and turn‐off instants, respectively. The auxiliary switch turns on under zero‐current switching and turns off under ZVZCS. Furthermore, the reverse recovery losses of diodes are reduced. The theoretical foundation of the proposed converter is presented and its performance is simulated by OrCAD software. The obtained results show 3.5% improvement in the efficiency at nominal loads, compared to its hard‐switching counterpart. A dual‐input prototype of the proposed structure is successfully built to support the validity of the theoretical analysis.
17 March 2020 in International Transactions on Electrical Energy Systems
7 February 2018 in Electric Power Components and Systems
Solar energy is a very cost efficient energy in terms of construction and maintenance that has no pollution and can be found everywhere. So, various converter topologies are used as an interface converter for solar panels. The boost converter is the conventional converter used in photovoltaic (PV) application. But, it has several problems such as instability in Continuous Conduction Mode (CCM), input inrush currents, short circuit protection and etc. These problems, lead to use Z-Source and quasi Z-Source Converter (qZSC) which have higher gain compared to traditional boost converter, lower current ripple at the input without using any extra filters, buck and boost capability, lower output ripple and higher reliability. In this paper a soft switching technique for qZSC converter with coupled inductor and without any auxiliary switch is proposed for PV application. By adding an auxiliary circuit, which includes a coupled inductor, diode and capacitor, soft switching condition is provided for all semiconductor elements of the proposed converter. The proposed converter is theoretically analyzed and to confirm the validity of the theoretical analysis, it is simulated by ORCAD and a laboratory prototype is built. The proposed converter shows six percent efficiency improvement in comparison with hard switching counterpart.
26 November 2025 in IEEE Transactions on Vehicular Technology
This study investigates the potential of enhancing regional rail efficiency and reducing emissions through the implementation of dual Electric Traction Machine (ETM) drivetrains. By employing two ETMs, optionally with different specifications and real-time load distribution, the research evaluates the impact on energy savings and battery longevity. The analysis is based on a comparative simulation study between single and dual ETM configurations, emphasizing energy consumption and environmental impact from both design and control perspectives. Simulation results for the Borlänge–Malung railway corridor in Sweden indicate that energy consumption can be reduced by approximately 15–20%, depending on the torque-sharing strategy and size ratio between the ETMs. The study further illustrates the operational inefficiencies inherent in single-ETM systems and highlights the performance gains of dynamic torque splitting in dual-ETM configurations. A specific control strategy is proposed: the smaller ETM is prioritized during cruising, while both machines are utilized under high-power demands such as acceleration. This approach optimizes energy usage without compromising performance, contributing to a more sustainable and cost-effective regional rail system. In terms of environmental impact, simulations based on the Swedish electricity mix show that the dual-ETM setup can reduce operational CO₂ emissions by approximately 80 tons over a 40-year service life. Moreover, improved battery utilization extends battery life, reducing manufacturing-related CO₂ emissions by an estimated 15 tons compared to the single-ETM configuration.
27 September 2021 in IEEE Transactions on Plasma Science
In this article, a new modular structure of Marx generators (MGs) based on interleaved boost converter is proposed. The converter operates in discontinuous conduction mode to generate a high-voltage pulsed power with a common low-voltage source. Unlimited stages can be added to the proposed structure to reach lower maximum voltage stress for the semiconductors or to generate several kilovolts of the output pulses, while the voltage of the semiconductors remains constant. This structure resulted in a higher pulse repetition rate, fewer semiconductor elements, and lower semiconductor voltage stress in comparison to conventional MGs. Hence, the proposed structure is applicable for and efficient in supplying plasma applications with high-voltage pulses. The theoretical foundation of the introduced converter is presented and its performance is simulated using OrCAD software. Based on the obtained results, the maximum voltage of the output pulse is 40 times the input voltage in a single-stage structure. An 80-W prototype of the proposed structure was built to validate the accuracy of the theoretical foundation and the simulation results.