4 December 2024 in IEEE Transactions on Nuclear Science
Commissioning of detector systems for the High-Luminosity Large Hadron Collider (HL-LHC) is scheduled to take place between 2026 and 2028 at CERN. Application Specific Integrated Circuits (ASICs) for those systems have been in intense development over the past ten years. Some of those ASICs, as is the case of the Low Power GigaBit Transceiver (lpGBT) described in this work, have now been produced in industrial quantities and have been fully qualified for operation in the HL-LHC environments that require, where the innermost detectors are concerned, radiation hardness in excess of 1 MGy. The lpGBT is a multi-functional device, enabling data transmission between the off-detector and the on-detector systems. Data can be transmitted from the detector at 5.12 Gbit s −1 and 10.24 Gbit s −1 and to the detector at 2.56 Gbit s −1 . It implements data rate-configurable electrical links to communicate with the front-end ASICs and low-speed serial and parallel buses for experiment control. A set of analog functions for monitoring and control of the physics detectors is also included. This paper describes the functionality and the architecture of the lpGBT ASIC and reports on its radiation hardness characterization.
4 June 2021 in IEEE Transactions on Nuclear Science
We present the design and test results of a time-to-digital-converter (TDC). The TDC will be a part of the readout Application-Specific Integrated Circuit (ASIC), called endcap timing read-out chip (ETROC), to read out low-gain avalanche detectors (LGADs) for the CMS endcap timing layer (ETL) of high-luminosity large hadron collider (LHC) upgrade. One of the challenges of the ETROC design is that the TDC is required to consume less than 200 μW for each pixel at the nominal hit occupancy of 1%. To meet the low-power requirement, we use a single delay line for both the time of arrival (TOA) and the time over threshold (TOT) measurements without delay control. A double-strobe self-calibration scheme is used to compensate for process variation, temperature, and power supply voltage. The TDC is fabricated in a 65-nm CMOS technology. The overall performances of the TDC have been evaluated. The TOA has a bin size of 17.8 ps within its effective dynamic range of 11.6 ns. The effective measurement precision of the TOA is 5.6 and 9.9 ps with and without nonlinearity correction, respectively. The TDC block consumes 97 μW at the hit occupancy of 1%. Over a temperature range from 23 °C to 78 °C and a power supply voltage range from 1.05 to 1.35 V (the nominal value of 1.20 V), the self-calibrated bin size of the TOA varies within 0.4%. The measured TDC performances meet the requirements except that more tests will be performed in the future to verify that the TDC complies with the radiation tolerance specifications.
1 April 2019 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
7 May 2019 in IEEE Transactions on Nuclear Science
We present the design and the test results of a dual-channel vertical-cavity surface-emitting laser (VCSEL) driver application-specific integrated circuit (ASIC) LOCld65 for detector front-end readout. LOCld65 is designed in a commercial 65-nm CMOS technology with a power supply of 1.2 V. LOCld65 contains two separate channels with the same structure and the two channels share an I 2 C slave. Each channel consists of an input amplifier, four stages of limiting amplifiers (LAs), a high-current output driver, and a bias-current generator. In order to extend the bandwidth, the input amplifier uses an inductive peaking technique and the LAs use a shared inductive peaking technique. The input amplifier and the output driver each utilize a continuous-time linear equalizer (CTLE). The LAs employ active feedback. The modulation current, the bias current, the peaking strength of the CTLEs, and the feedback strength of LAs are programmable through an I 2 C interface. In order to protect from the radiation damage, the I 2 C slave is implemented with triple modular redundancy. Each channel of LOCld65 is tested to operate up to 14 Gb/s with typical power dissipations (the VCSEL included) of 68.3 and 62.1 mW/channel at the VCSEL voltages of 3.3 and 2.5 V, respectively. LOCld65 survives 4.9 kGy(SiO 2 ). LOCld65 is an excellent match for the serializer-deserializer ASIC low power giga bit transceiver in single- or dual-channel optical transmitters in high-luminosity Large Hadron Collider (HL-LHC) upgrade applications.
13 January 2023 in IEEE Transactions on Nuclear Science
This paper presents the design and test results of a 14-Gbps Vertical-Cavity Surface-Emitting Laser (VCSEL) driving ASIC based on a commercial 65 nm CMOS technology with a novel power efficient driving structure. This VCSEL driver consists of an input equalizer stage, a pre-driver stage, an output driver stage, and their bias circuits. The equalizer stage uses the continuous time linear equalizer (CTLE) structure to compensate for the high-frequency attenuation. The pre-driver stage is composed of two stage limiting amplifiers with a shared inductor structure. The proposed output driver stage adopts a novel complementary-modulated method to fully utilize the currents in both branches of the conventional differential structure. In addition, a self-adjusting CTLE pre-emphasis with edge peaking function is combined in the output stage to improve the bandwidth and boost the falling edge of the output current signal. This VCSEL driving ASIC has been fully tested with a real VCSEL load, and the wide-open optical eye diagrams have been captured at a 14-Gbps data rate with a power consumption of 44 mW. The peak-to-peak jitter of the 14-Gbps optical eye diagram is 15.8 ps with a random jitter of 3.02 ps.
1 May 2022 in Journal of Instrumentation
The Quad transimpedance and limiting amplifier (QTIA) is a 4-channel array optical receiver ASIC, developed using a 65 nm CMOS process. It is configurable between the bit rate of 2.56 Gbps and 10 Gbps per channel. QTIA offers careful matching to both GaAs and InGaAs photodiodes. At this R&D stage, each channel has a different biasing scheme to the photodiode for optimal coupling. A charge pump is implemented in one channel to provide a higher reverse bias voltage, which is especially important to mitigate radiation effects on the photodiodes. The circuit functions of QTIA successfully passed the lab tests with GaAs photodiodes.