11 February 2016 in Journal of Lightwave Technology
This paper summarizes recent work on the use of optical wireless links as a robust outdoor backhaul solution for small radio cells, such as WiFi, LTE and 5G, over distances between 20 and 200 m. Results of a 5-month outdoor field trial in Berlin, Germany, indicate that the visibility range was never below 180 m, with more than 1 km in 99% of all times during this period. Rate-adaptive transmission proved to improve the availability remarkably in the occasional presence of fog or sunlight. A mathematical model of the backhaul link including these impairments is presented and implemented to obtain an optimized link design. A prototype was realized, accordingly, using low-cost optoelectronic components and a 1 Gb/s baseband chipset. Gross data rates of 800, 500, and 225 Mb/s have been achieved in real-time operation over 20, 100, and 215 m outdoor link distance, respectively, with 2 ms latency at 95% load. Finally, we discuss further evolution towards 5G mobile networks.
29 March 2021 in Journal of Lightwave Technology
We present a concept for networked optical wireless communications, also denoted as LiFi, to meet the requirements of industrial wireless applications. These are primarily mobility support with moderate data rates per device, reliable real-time communication, and integrated positioning. We describe a distributed multiuser multiple-input multiple-output architecture, serving mobile devices via an optical wireless infrastructure. The system consists of a central unit, being connected to a number of distributed optical frontends covering a larger area. Our main contribution is a medium access control protocol based on space division multiple access. Evaluation results demonstrate the advantages of joint transmission from adjacent optical frontends and the dynamic switching between spatial diversity and multiplexing. The relevance of spatial multiplexing becomes obvious through channel measurements in an indoor scenario. Moreover, we highlight a low-power physical layer based on on-off-keying for battery-powered mobile devices. Our architecture can easily integrate positioning by simultaneously measuring the time-of-flight between multiple optical frontends and the mobile device. We highlight the use of plastic optical fiber as an analog fronthaul technology and discuss the integration with other networks. The main functions described in this paper will be supported by the upcoming IEEE Std 802.15.13.
26 February 2018 in Circuits, Systems, and Signal Processing
The concept of frequency interleaving (FI) for digital-to-analog converters (DACs) has recently experienced renewed interest, in order to overcome the DACs’ bandwidth limitations. In this concept, the output signals of multiple DACs are interleaved in the frequency domain in order to generate a combined output signal that exceeds both the sampling rate and the bandwidth of a single DAC. In this paper, a mathematical framework for FI-DACs with a large number of DACs is presented and the inherent interdependencies between sampling rate, the number of samples, LO frequencies, symbol rate and analog frequency responses are highlighted. A mathematical expression for the distribution of data samples among the DACs is presented, taking into account bandwidth limitations of the analog components as well as guard bands to mitigate cross talk. In order to balance the FI-DAC’s parameters a mathematical optimization approach is introduced and illustrated with examples. Both simulation and experimental results validate the FI-DAC concept, and an outlook on implementation issues completes this paper.
11 December 2017 in Journal of Lightwave Technology
We present high-speed single channel discrete multitone (DMT) operations of directly modulated 850 nm vertical cavity surface emitting lasers (VCSEL). Successful transmission of 135 Gb/s over 10 m of OM4 multi-mode fiber (MMF) and 114 Gb/s over 550 m is demonstrated below the 7% overhead hard-decision forward error correction (7% HD-FEC) bit error rate (BER) limit. At higher BER limits, i.e. 20% overhead soft decision FEC, which are of arising interest for these high-speed short-range links, data rates of up to 161 Gb/s are presented. This is enabled by high bandwidth, low noise VCSELs, which operate in quasi single-mode to overcome the mode dispersion limitations of the MMF. The applied modulation format is discrete multitone in combination with a Volterra filter based pre-distortion approach, which pre-compensates the linear and nonlinear behavior of the transmission system, primarily the digital-analog converter, the VCSEL, the MMF and the photoreceiver. Furthermore, a detailed investigation of the pre-distortion is given by experimental means, showing that the optimum amount of pre-distortion depends on the applied components and the signal bandwidth. This makes it challenging to predict the optimum, however a pure electrical pre-distortion offers already a fair gain in performance.
25 May 2021 in Journal of Lightwave Technology
We present a digital signal processing (DSP) scheme that performs hyperparameter tuning (HT) via Bayesian optimization (BO) to autonomously optimize memory tap distribution of Volterra series and adapt parameters used in the synthetization of a digital pre-distortion (DPD) filter for optical transmitters. Besides providing a time-efficient technique, this work demonstrates that the self-adaptation of DPD hyperparameters to correct the component-induced nonlinear distortions as different driver amplifier (DA) gains, symbol rates and modulation formats are used, leads to an improvement in transmitter performance. The scheme has been validated in back-to-back (b2b) experiments using dual-polarization (DP) 64 and 256 quadrature amplitude modulation (QAM) formats, and symbol rates of 64 and 80 GBd. For DP-64QAM at 64 GBd, it is shown that the DPD scheme reduces the required optical signal-to-noise ratio (OSNR) at a bit error ratio of 10-2 by 0.9 dB and 0.6 dB with respect to linear DPD and a heuristic nonlinear DPD approach, respectively. Moreover, we show that the proposed approach also reduces filter complexity by 75% in conjunction with the use of memory polynomials (MP), while achieving a similar performance to Volterra pre-distortion filters.
14 February 2024 in IEEE Access
Terahertz wireless communications is an increasingly interesting research topic due to the high demand for un-allocated channels and high data rates. Photonic solutions have shown great potential in this field. However, most photonics assisted THz links so far have employed optoelectronics only on the transmit side. Thus, the full potential of photonic THz communication has not been utilized yet. Here, we introduce optoelectronics also on the receive side by using a photoconductive antenna based heterodyne THz detector. This allows down-conversion of data signals from the W-, D-, and THz-band to the baseband using a laser beat signal as local oscillator. Using electromagnetic modeling, we designed passive radio frequency structures and a receiver package to handle high intermediate frequency output signals. In a homodyne spectroscopic setup, the receiver shows a frequency response superior to state-of-the-art photoconductive antennas due to an improved photoconductive material. In a heterodyne testbed, the receiver exhibits a large intermediate frequency bandwidth of 11 GHz and a conversion gain of -47 dB. This enabled us to employ the receiver in a fully photonic wireless link at sub-terahertz and terahertz frequencies together with a PIN photodiode emitter. We achieved error-free transmission of 4-QAM signals with gross data rates up to 12 Gbit/s at carrier frequencies up to 320 GHz. This work shows the huge potential of optoelectronic receivers for THz wireless communications and enables the exploration of full photonic THz links.