The drying of electrodes represents a critical process step in the production of lithium‐ion batteries. In this process step, unfavorably adjusted drying conditions can result in deteriorated electrode properties. Furthermore, the process speed is restricted by limited heat and mass transfer in purely convective drying. To counteract those effects, energy input by near‐infrared (NIR) radiation is a promising approach. Herein, analytical considerations are carried out to demonstrate the suitability of infrared radiation with regard to achievable electrode temperatures and drying rates. In an experimental approach, aqueous processed graphite anodes are dried with an NIR module, varying the power and the amount of convection for different experiments. The temperature profiles of the electrodes and the drying rates are measured and analyzed, and the electrodes are subsequently characterized using adhesion measurements. The results obtained show that energy input by NIR radiation during the drying of electrodes can lead to an increased drying speed, electrode temperature during drying, and adhesion force of the dry electrode. These findings indicate that the binder distribution during NIR drying is advantageous in terms of electrode adhesion, compared with convectively dried electrodes produced at comparable drying rates, positioning the process promisingly with regard to high throughput rates.
In this work, a detailed study of the drying of battery electrodes of different thicknesses is presented. A mathematical model to calculate the solvent loading and film temperature over the drying time is experimentally validated. The model is based on a first study presenting a simulation model to predict the drying course when linear drying kinetics prevail and no resistance exists for solvent transport within the film. To shed some light on the drying behavior of electrode films with different thicknesses, the start of capillary pore emptying is observed using a digital microscope. In the experiments, an onset of capillary transport even before the end of film shrinkage is observed for the electrode films with thicknesses above state‐of‐the‐art‐thickness. A clusterwise drying behavior becomes more distinct for thicker electrodes, with large areas of dry and wet capillaries next to each other, compared to a more homogenous drying of the thin electrodes. Based on these findings, the linear model is extended to consider transport limitations within the porous electrode film in the form of a moving drying front. The experiments show an increasing deviation from the linear model with increasing electrode thickness and the extended simulation, which considers transport resistances within the film, shows good agreement.
The drying of solvent‐processed electrodes is a critical process step in the manufacturing of lithium‐ion batteries. The technology used to introduce the energy required for drying into the material, combined with the specified process parameters, significantly influences the resulting electrode properties. A major challenge is to counteract binder migration effects that may occur during drying of the porous electrode structure, causing a decrease in adhesion and electrochemical performance, especially for high drying rates. From this motivation, investigations on the influence of process design during near‐infrared drying of aqueous‐processed graphite anodes are carried out. A multistage drying design with varying parameters in specific drying sections with energy input by radiation is applied. The results show that the specific application of a three‐stage drying profile in combination with energy input by radiation enables a significant decrease in drying time by at least 60% while the electrode properties can be preserved. These findings indicate a beneficial development of binder distribution as a consequence of multistage NIR drying, evidenced by adhesion and electrochemical performance. Finally, the application of the multistage drying profile is theoretically transferred to an industrial‐scale roll‐to‐roll dryer, whereby the necessary dryer length can be reduced by 53%.
Moisture management and postdrying are crucial for Li‐ion battery lifetime and performance as well as overall energy efficiency of electrode production. An optimization of these processes by a fundamental comprehension of sorption and mass transport mechanisms in the electrode holds potential to increase sustainability of this technology. The composition of electrodes determines which of these mechanisms govern the interaction of electrodes with water from atmosphere. In this study, the influence of the binder system, temperature, and pressure of Li‐ion battery anodes on postdrying is focused on. Anodes with the binder system carboxymethylcellulose (CMC)/styrene–butadiene–rubber (SBR) and polyvinylidene fluoride represent a mostly absorbing and mostly adsorbing material system, respectively. Variation of the process parameters temperature and pressure reveals that both material systems show a similar impact of pressure on water mass transport in the electrode during water removal, although a reduced pressure impact for the CMC/SBR system is expected, since in this case most water is absorbed into the polymers and should diffuse independently of the system pressure. Temperature affects water mass transport in the absorbing material system stronger than in the adsorbing material system, due to the strong temperature dependency of the water diffusion inside the absorbing polymers.