Inkjet printing of graphene inks is considered to be very promising for wearable e-textile applications as benefits of both inkjet printing and extra-ordinary electronic, optical and mechanical properties of graphene can be exploited. However, the common problem associated with inkjet printing of conductive inks on textiles is the difficulty to print a continuous conductive path on a rough and porous textile surface. Here we report inkjet printing of an organic nanoparticle based surface pre-treatment onto textiles to enable all inkjet-printed graphene e-textiles for the first time. The functionalized organic nanoparticles present a hydrophobic breathable coating on textiles. Subsequent inkjet printing of a continuous conductive electrical path onto the pre-treated coating reduced the sheet resistance of graphene-based printed e-textiles by three orders of magnitude from 1.09 × 106 Ω sq−1 to 2.14 × 103 Ω sq−1 compared with untreated textiles. We present several examples of how this finding opens up opportunities for real world applications of printed, low cost and environmentally friendly graphene wearable e-textiles.
Flexible fiber-shaped energy storage devices: principles, progress, applications and challenges Jing Ren, Quanfu Xu and Yi-Gang Li-Highly conductive templated-graphene fabrics for lightweight, flexible and foldable supercapacitors Ping Zhang, Hanzhi Zhang, Casey Yan et al.-Recent citations An outlook on printed microsupercapacitors: technology status, remaining challenges and opportunities J. Coelho et al-Recent Advances in Design of Flexible Electrodes for Miniaturized Supercapacitors Chenyang Yu et al-Resistance variation of conductive ink applied by the screen printing technique on different substrates
The morphology and organic field effect transistor (OFET) properties of two component blends of semi-crystalline 6,13-bis(triisopropylsilylethinyl)pentacene (TIPS-pentacene) with selected amorphous and semi-crystalline side chain aromatic low permittivity insulating binders deposited at room temperature under vacuum from a good solvent are reported. When blended with an amorphous binder there is evidence from X-ray photoelectron spectroscopy (XPS) of a strong interaction between TIPS-pentacene and the binder in the solidified film giving rise to twisted TIPS-pentacene crystals containing dislocations. Due to this strong interaction we see no evidence of segregation of TIPS-pentacene towards the active interface and hence we observe a rapid fall off in saturated hole mobility at an active concentration less than 50 wt%. When blended with a crystalline binder there is no evidence from XPS of any interaction between TIPS-pentacene and the binder in the solidified film. We propose that when a semi-crystalline binder is used, which crystallizes more slowly from solution than TIPS-pentacene, we observe stratification of the active material to both interfaces and as a result retention of saturated hole mobility even down to 10 wt%. The potential applications of the approach are in the formulation of low-cost organic semiconductors whose solution and solid state properties can be fine-tuned by careful binder selection.
16 September 2010 in Journal of Materials Chemistry
The positive effects on the inkjet drop ejection process, thin film morphology and subsequent thin film transistor performance caused by the blending a low molar mass semi-crystalline organic semiconductor, 6,13-triisopropylsilylethynylpentacene (TIPS-pentacene), with a low ε dielectric polymer, polystyrene (350 kDa) are reported. The presence of the high molecular weight polymer at a reduced concentration c/c* = 0.44 gives greater control of the drop generation process (when compared to low molar mass semi-crystalline organic semiconductor alone) due to stabilisation of the ligament break-up process with pinch off occuring at the nozzle plate and satellites coalescing within the main droplet. The addition of a small fraction of a high boiling point solvent results in the removal of droplet drying artefacts by generating a Marangoni flow in which double convection counteracts coffee stain formation. This results in more uniform solute coverage over the substrate, simplifying the print process. Whilst TIPS-pentacene and amorphous polystyrene do not undergo gross phase separation irrespective of deposition process the degree of crystallinity and extent of TIPS-pentacene stratification to the active interface was found to be strongly process dependant. Whilst a lower degree of crystallinity is observed when a dual solvent mixture is used there is strong evidence of greater stratification of the TIPS-pentacene at the active interface resulting in higher saturated hole mobility.
6 January 2015 in Journal of Materials Chemistry C
Inkjet printing of functional frequency selective surfaces (FSS) and radio frequency identification (RFID) tags on commercial paper substrates using silver nanoparticle inks sintered using low temperature thermal, plasma and photonic techniques is reported. Printed and sintered FSS devices demonstrate performances which achieve wireless communication requirements having a forward transmission scattering parameter, S21, depth greater than −20 dB at 13 GHz. Printed and plasma sintered RFID tags on transfer paper, which are capable of being mounted on skin, improved read distances compared to previously reported single layer transfer RFID tags fabricated by conventional thermal sintering.
1,4,8,11-Methyl-substituted 6,13-triethylsilylethynylpentacene shows extended π–π overlap when deposited from solution, yielding organic thin film transistors with high and reproducible hole mobility with negligible hysteresis.