3 January 2019 in Experiments in Fluids
5 January 2023 in Experiments in Fluids
The laminar separation bubble (LSB) that forms on the suction side of a modified NACA $$64_3$$ -618 airfoil at a chord-based Reynolds number of $$\textrm{Re} = 200,000$$ is studied using wind tunnel experiments. First, the LSB is characterized over a range of static angles of attack, in terms of the locations of separation, transition and reattachment—using surface pressure measurements, particle image velocimetry (PIV) and infrared thermography (IT). For the conditions tested, excellent agreement between the techniques is obtained. Subsequently, a pitching motion is imposed on the wind tunnel model, with reduced frequencies up to $$\text {\textit{k} = 0.25}$$ . While surface pressure measurements and PIV are not affected by the change in experimental conditions, the infrared approach is impaired by the thermal response of the surface. To overcome this, an extension of the differential infrared thermography (DIT) method for detecting the three characteristics of an unsteady LSB is considered. All three experimental techniques indicate a hysteresis in bubble location between the pitch up and pitch down phases of the motion, caused by the effect of the aerodynamic unsteadiness on the adverse pressure gradient. However, the DIT measurements suggest a larger hysteresis, which is attributed to the thermal response time of the model surface. The experimental results measured with the pressure sensors reveal that the hysteresis in bubble location is larger than the hysteresis in lift, indicating that the observed bubble hysteresis is not purely due to instantaneous flow conditions, but has an inherent component as well.
16 October 2019 in Measurement Science and Technology
Advanced data processing methods for detecting unsteady boundary layer transition in periodic aerodynamic processes by means of infrared thermography measurements are presented. The thermal radiation emitted from the heated suction surface of a pitching airfoil model in subsonic flow is measured with an infrared camera. The unsteady boundary layer transition location is detected by analyzing the difference in the infrared radiation signal over short periods of time with differential infrared thermography (DIT). The DIT method is optimized and automated in the present study, which facilitates the extension of the part of the motion period where valid DIT transition measurements are produced. Additionally, a new infrared thermography data processing method is introduced in this study. The extraction of the extrema of the measured radiation signal at fixed locations on the model surface yields instants of the motion period that relate to the occurrence of boundary layer transition. The local infrared thermography (LIT) approach can be extended to measuring the two-dimensional unsteady boundary layer transition front.
1 July 2023 in AIAA Journal
JFJosé L. Costa Fernández
The aeroelastic response of the Delft–Pazy wing to steady and periodic unsteady inflow conditions is analyzed experimentally. The Delft–Pazy wing is a highly flexible wing model based on the benchmark Pazy wing (Avin, O., Raveh, D. E., Drachinsky, A., Ben-Shmuel, Y., and Tur, M., “Experimental Aeroelastic Benchmark of a Very Flexible Wing,” AIAA Journal, Vol. 60, No. 3, 2022, pp. 1745–1768) and exhibits wingtip displacements of more than 24% of the span in the present study. The nonintrusive measurements are performed with an integrated optical approach that provides combined measurements of the structural response of the wing and the unsteady flowfield around it. The aeroelastic loads acting on the wing are derived using physical models and validated against force balance measurements, showing a good agreement for all considered inflow conditions. The analysis of the aeroelastic response of the wing to the unsteady inflow produced by a gust generator shows that both structural and aerodynamic responses depend strongly on the frequency of the gust. The results of this study provide a characterization of the aeroelastic behavior of the Delft–Pazy wing and can serve as a reference for the development of novel and improved nonlinear aeroelastic simulation models.
26 May 2023 in Journal of Aircraft
This study presents an aeroelastic wind-tunnel experiment to identify the influence of the wing stiffness and hinge release threshold on the gust load alleviation performance of a folding wingtip design. Five models with different stiffness and tailoring properties are tested, and the wing root bending moment at different conditions is compared to the response with the locked-hinge condition to assess the impact on the gust load alleviation capabilities of the folding wingtip. The results show that the structural properties do not have an important impact on the peak load alleviation but the hinge release threshold and timing do. Releasing with the correct timing can reduce significantly the peak loads. However, the dynamics of the system are affected by this release; the flutter speed is decreased, and, although the performance can improve, load oscillations increase, which can be considered detrimental for reasons such as fatigue or passenger comfort.