Jimi Tjong

Jimi Tjong

Auto-generated profile, based on publicly available information

Jimi Tjong

PERDC, Ford, Windsor, ON N9A 6X3, Canada

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 May 2019 in ACS Nano
Verified
Journal Article
Closed access
MSMaria Semeniuk
Maria Semeniuk
ZYZhihui Yi
Zhihui Yi
VPVida Poursorkhabi
Vida Poursorkhabi
JTJimi Tjong
Jimi Tjong
SJShaffiq Jaffer
Shaffiq Jaffer
MSMohini Sain
Mohini Sain

1 August 2018 in Applied Surface Science
Verified
Journal Article
Closed access
ZYZhihui Yi
Zhihui Yi
YZYongbiao Zhao
Yongbiao Zhao
PLPeicheng Li
Peicheng Li
KHKevin Ho
Kevin Ho
NBNykola Blozowski
Nykola Blozowski
ZLZheng-Hong Lu
Zheng-Hong Lu

1 October 2015 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
UAUsman Asad
Usman Asad
MZMing Zheng
Ming Zheng
DTDavid Ting
David Ting
JTJimi Tjong
Jimi Tjong
Homogeneous charge compression ignition (HCCI) combustion in diesel engines can provide cleaner operation with ultralow NOx and soot emissions. While HCCI combustion has generated significant attention in the last decade, however, till date, it has seen very limited application in production diesel engines. HCCI combustion is typically characterized by earlier than top-dead-center (pre-TDC) phasing, very high-pressure rise rates, short combustion durations, and minimal control over the timing of the combustion event. To offset the high reactivity of the diesel fuel, large amounts of exhaust gas recirculation (EGR) (30–60%) are usually applied to postpone the initiation of combustion, shift the combustion toward TDC, and alleviate to some extent, the high-pressure rise rates and the reduced energy efficiency. In this work, a detailed analysis of HCCI combustion has been carried out on a high-compression ratio (CR), single-cylinder diesel engine. The effects of intake boost, EGR quantity/temperature, engine speed, injection scheduling, and injection pressure on the operability limits have been empirically determined and correlated with the combustion stability, emissions, and performance metrics. The empirical investigation is extended to assess the suitability of common alternate fuels (n-butanol, gasoline, and ethanol) for HCCI combustion. On the basis of the analysis, the significant challenges affecting the real-world application of HCCI are identified, their effects on the engine performance quantified, and possible solutions to overcome these challenges explored through both theoretical and empirical investigations. This paper intends to provide a comprehensive summary of the implementation issues affecting HCCI combustion in diesel engines.

30 September 2014 in Journal of Energy Resources Technology
Verified
Journal Article
Closed access
PDF file
TYTadanori Yanai
Tadanori Yanai
XHXiaoye Han
Xiaoye Han
GRGraham T. Reader
Graham T. Reader
MZMing Zheng
Ming Zheng
JTJimi Tjong
Jimi Tjong

22 July 2020 in Nanomaterials
Verified
Journal Article
Open access
PDF file
AGAntimo Graziano
Antimo Graziano
ODOtavio Augusto Titton Dias
Otavio Augusto Titton Dias
CGChristian Garcia
Christian Garcia
SJShaffiq Jaffer
Shaffiq Jaffer
JTJimi Tjong
Jimi Tjong
MSMohini Sain
Mohini Sain
This research work is the first to report thermal stability, heat deformation resistance, and crystallization behavior of a Polyethylene (PE)-based biphasic polyolefin system reinforced with Reduced Graphene Oxide (RGO), which was obtained through Graphene Oxide (GO) chemical reduction. Polypropylene (PP) represented the polymeric dispersed phase. A strategic PE/PP/RGO manufacturing procedure was employed to thermodynamically localize RGO at the PE/PP interface, as confirmed by Transmission Electron Microscopy (TEM), bringing a uniform micro phase dispersion into the macro phase. In addition, studies of PE non-isothermal crystallization kinetics indicated that the morphology tunable micro phase and the nanolayered RGO promoted a nucleation-controlled PE crystallization, which was supported by Polarized Light Optical Microscopy (PLOM). This, together with fine morphology, justified the remarkable enhancement registered for the ternary system’s thermal stability and heat deformation resistance. Different filler loads were employed, with weight fractions of 2% and 4%. It was observed that the former, being better exfoliated and more homogeneously distributed at the PE/PP interface than the latter, led to a more improved PE crystallization, alongside a greater ternary system’s thermal properties. Moreover, the thermal stability of PE/PP reinforced with 2% of RGO was even higher than that of virgin PP, while their heat deformation resistance values were found to be similar. Therefore, this unique outcome provides industries, such as the energy and automotive sectors, with the opportunity to substitute PP-rich products with those mostly comprised of a cheaper, more abundant, yet performant PE.

21 September 2012 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
XHXiaoye Han
Xiaoye Han
KXKelvin Xie
Kelvin Xie
JTJimi Tjong
Jimi Tjong
MZMing Zheng
Ming Zheng
Diesel low temperature combustion (LTC) is capable of producing diesel-like efficiency while emitting ultra-low nitrogen oxides (NOx) and soot emissions. Previous work indicates that well-controlled single-shot injection with exhaust gas recirculation (EGR) is an operative way of achieving diesel LTC from low to mid engine loads. However, as the engine load is increased, demanding intake boost and injection pressure are necessary to suppress high soot emissions during the transition to LTC. The use of volatile fuels such as ethanol is deemed capable of promoting the cylinder charge homogeneity, which helps to overcome the high soot challenge and, thus, potentially expand the engine LTC load range. In this work, LTC investigations were carried out on a high compression ratio (18.2:1) engine. Engine tests were first conducted with diesel and LTC operation at 8 bar indicated mean effective pressure (IMEP) was enabled by sophisticated control of the injection pressure, injection timing, intake boost, and EGR application. The engine performance was characterized as the baseline, and the challenges were identified. Further tests were aimed to improve the engine performance against these baseline results. Experiments were, hence, conducted on the same engine with secondary ethanol port fuelling (PF). Single-shot diesel direct injection (DI) was applied close to top dead center (TDC) to ignite the ethanol and control the combustion phasing. The control sensitivity was studied through injection timing sweeps and EGR sweeps. Additional tests were performed to investigate the ethanol-to-diesel ratio effects on the mixture reactivity and the engine emissions. Engine load was also raised to 16.4 bar IMEP while keeping the simultaneously low NOx and soot emissions. Significant improvement of engine control and emissions was achieved by the DI+PF strategy.