Edvinas Krugly

Edvinas Krugly

Auto-generated profile, based on publicly available information

Edvinas Krugly

Department of Environmental Technology, Kaunas University of Technology, LT-50254 Kaunas, Lithuania

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 February 2022 in Carbohydrate Polymers
Verified
Journal Article
Closed access
EKEdvinas Krugly
Edvinas Krugly
IPIngrida Pauliukaityte
Ingrida Pauliukaityte
DCDarius Ciuzas
Darius Ciuzas
MBMindaugas Bulota
Mindaugas Bulota
LPLaura Peciulyte
Laura Peciulyte
DMDainius Martuzevicius
Dainius Martuzevicius

5 April 2020 in Polymers
Verified
Journal Article
Open access
PDF file
Samy YousefSamy Yousef
Samy Yousef
ZSZahid Sarwar
Zahid Sarwar
JŠJustas Šereika
Justas Šereika
NSNerijus Striugas
Nerijus Striugas
EKEdvinas Krugly
Edvinas Krugly
DMDainius Martuzevicius
Dainius Martuzevicius
Polyether block amide (PEBA) nanocomposite membranes, including Graphene (GA)/PEBA membranes are considered to be a promising emerging technology for removing CO2 from natural gas and biogas. However, poor dispersion of GA in the produced membranes at industrial scale still forms the main barrier to commercialize. Within this frame, this research aims to develop a new industrial approach to produce GA/PEBA granules that could be used as a feedstock material for mass production of GA/PEBA membranes. The developed approach consists of three sequential phases. The first stage was concentrated on production of GA/PEBA granules using extrusion process (at 170–210 °C, depending on GA concentration) in the presence of Paraffin Liquid (PL) as an adhesive layer (between GA and PEBA) and assisted melting of PEBA. The second phase was devoted to production of GA/PEBA membranes using a solution casting method. The last phase was focused on evaluation of CO2/CH4 selectivity of the fabricated membranes at low and high temperatures (25 and 55 °C) at a constant feeding pressure (2 bar) using a test rig built especially for that purpose. The granules and membranes were prepared with different concentrations of GA in the range 0.05 to 0.5 wt.% and constant amount of PL (2 wt.%). Also, the morphology, physical, chemical, thermal, and mechanical behaviors of the synthesized membranes were analyzed with the help of SEM, TEM, XRD, FTIR, TGA-DTG, and universal testing machine. The results showed that incorporation of GA with PEBA using the developed approach resulted in significant improvements in dispersion, thermal, and mechanical properties (higher elasticity increased by ~10%). Also, ideal CO2/CH4 selectivity was improved by 29% at 25 °C and 32% at 55 °C.

17 February 2020 in Materials
Verified
Journal Article
Open access
PDF file
VKVytautas Kavaliūnas
Vytautas Kavaliūnas
EKEdvinas Krugly
Edvinas Krugly
MSMantas Sriubas
Mantas Sriubas
HMHidenori MIMURA
Hidenori MIMURA
GLGiedrius Laukaitis
Giedrius Laukaitis
YHYoshinori Hatanaka
Yoshinori Hatanaka
The present study investigates Mg (0 ÷ 17.5 wt %), Cu (0 ÷ 21 wt %) and Ni (0 ÷ 20.2 wt %) dopants (M-doped) influence on photocatalytic activity of amorphous TiO2 thin films. Magnetron sputtering was used for the deposition of M-doped TiO2 thin films. According to SEM/EDS surface analysis, the magnetron sputtering technique allows making M-doped TiO2 thin films with high uniformity and high dopant dispersion. Photocatalysis efficiency analysis was set in oxalic acid under UV irradiation. In accordance with the TOC (total organic carbon) measurements followed by the apparent rate constant (kapp) results, the dopants’ concentration peak value was dopant-dependent; for Mg/TiO2, it is 0.9% (kapp—0.01866 cm−1), for Cu/TiO2, it is 0.6% (kapp—0.02221 cm−1), and for Ni/TiO2, it is 0.5% (kapp—0.01317 cm−1). The obtained results clearly state that a concentration of dopants in TiO2 between 0.1% and 0.9% results in optimal photocatalytic activity.

18 August 2021 in Pharmaceutics
Verified
Journal Article
Open access
PDF file
LDLauryna Dabasinskaite
Lauryna Dabasinskaite
EKEdvinas Krugly
Edvinas Krugly
OBOdeta Baniukaitiene
Odeta Baniukaitiene
DMDainius Martuzevicius
Dainius Martuzevicius
DCDarius Ciuzas
Darius Ciuzas
AUArvydas Usas
Arvydas Usas
Ozonation has been proved as a viable surface modification technique providing certain properties to the scaffolds that are essential in tissue engineering. However, the ozone (O3) treatment of PCL scaffolds in aqueous environments has not yet been presented. O3 treatment performed in aqueous environments is more effective compared with traditional, executed in ambient air treatment due to more abundant production of hydroxyl radicals (•OH) within the O3 reaction with water molecules. During interaction with •OH, the scaffold acquires functional groups which improve wettability properties and encapsulate growth factors. In this study, a poly(ε)caprolactone (PCL) scaffold was fabricated using solution electrospinning and was subsequently ozonated in a water reactor. The O3 treatment resulted in the expected occurrence of oxygen-containing functional groups, which improved scaffold wettability by almost 27% and enhanced cell proliferation for up to 14 days. The PCL scaffold was able to withhold 120 min of O3 treatment, maintaining fibrous morphology and mechanical properties.

1 February 2022 in Building and Environment
Verified
Journal Article
Closed access
EKEdvinas Krugly
Edvinas Krugly
OPOleh Pitak
Oleh Pitak
DCDarius Ciuzas
Darius Ciuzas
MTMartynas Tichonovas
Martynas Tichonovas
ISInga Stasiulaitiene
Inga Stasiulaitiene
DMDainius Martuzevicius
Dainius Martuzevicius

13 August 2021 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
DCDarius Ciuzas
Darius Ciuzas
EKEdvinas Krugly
Edvinas Krugly
SSSimona Sriubaite
Simona Sriubaite
IPIngrida Pauliukaityte
Ingrida Pauliukaityte
OBOdeta Baniukaitiene
Odeta Baniukaitiene
DMDainius Martuzevicius
Dainius Martuzevicius