30 April 2024 in International Journal of 3D Printing Technologies and Digital Industry
Ni-Hard cast iron materials are frequently used in equipment where high wear resistance is required in industrial applications. Generally, Ni-Hard is produced by conventional casting techniques. In this study, it was aimed to produce Ni-Hard powders to produce Ni-Hard cast iron materials with additive manufacturing techniques. To produce spherical and fine raw materials for additive manufacturing techniques, the gas atomization technique with a close-coupled nozzle system was preferred for the production of Ni-Hard powders. Ni-Hard alloy was melted in a high-frequency 10kW induction furnace under a protective atmosphere integrated into the gas atomization system. During the atomization process, 150 °C superheating was applied to prevent the liquid metal from freezing and clogging the melt delivery tube. In terms of the continuity of the atomization process, the negative pressure (aspiration pressure) values formed at the end of the melt delivery tube at different gas pressures were measured. An aspiration pressure of -50 mbar was obtained under an atomization pressure of 35 bar. Particle size distributions, hall flow behaviour and angle of repose properties of the produced powders were determined. Finally, the characterization of the powders was carried out by scanning electron microscopy. It was determined that the powders obtained as a result of atomization exhibited a spherical morphology and a narrow size range. The Hall flow rate test result of Ni-Hard powders was measured as 22 seconds for 50 g.
30 September 2026 in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
Bu çalışma, AlSi kaplamalı SABC1470 çeliği kullanılarak direnç nokta kaynağı ile yapılan patchwork üretim yönteminin, sıcak şekillendirme prosesi öncesi ve sonrasında mikroyapısal ve mekanik davranışlarının, kaynaklanabilirlik fizibilitesi üzerindeki etkilerini analiz etmeyi amaçlamaktadır. Deneysel çalışmalar kapsamında, aynı kalınlığa ve malzeme özelliğine sahip iki sac plaka, direnç nokta kaynak yöntemi ile birleştirilmiş ve farklı kaynak parametrelerinin kaynak çekirdek çapına ve mikroyapıya etkisi detaylı olarak incelenmiştir. Spot kaynağı sonrası uygulanan presle bükme işlemi ile radius bölgelerinde meydana gelen yapısal değişimler taramalı elektron mikroskobu (SEM) yardımıyla analiz edilmiştir. Özellikle çekirdek çapının standartlara uygunluğu değerlendirilmiş; sıcak şekillendirme prosesi sonrasında spot çekirdeğinde meydana gelen kayma ve çatlak oluşumları ile ilişkisi ortaya konmuştur. Bu bulgular, direnç nokta kaynağı ile yapılan patchwork uygulamalarında kaynak kalitesinin ve mikroyapısal bütünlüğün üretim sonrası şekillendirme davranışı üzerindeki belirleyici etkisini göstermektedir.
29 September 2025 in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
Material selection for creating a rigid and high-energy absorption lightweight BIW is critical in terms of fuel economy and emissions. In this context, material forming limits and mechanical behavior during stamping processes are the most important factors in the creation of lightweight BIW’s. Therefore, enhancing strength and reducing material thickness stand out as the primary ways to comply with industry standards and reduce the body weight. In weight reduction efforts with dual-phase steels, thinning may lead to splitting due to the increased martensitic island structure in regions with the highest Mn and C content in dual-phase materials. In hot- and cold-rolled dual-phase 800DU material with a thickness of 1mm, splitting may occur during forming simulation due to the martensitic structure to distribute inhomogeneously, surpassing the critical threshold of the forming simulation curve when compared to cold-rolled 600DU material with a thickness of 1.2mm. This study addresses the thinning-induced splitting issue encountered in weight reduction applications, determining the optimal choice between different rolling types under a die produced for 600DU material with a thickness of 1.2mm, using both hot and cold-rolled materials. In line with the purpose of the study, trials were conducted with two different 800DU materials under forming dies. Formability simulations and mechanical tests were performed, and analyses were carried out in terms of microstructure, thinning, and edge cracking performance. The characterization of the materials was conducted using a scanning electron microscope (SEM) equipped with an EDX apparatus. Following the characterization, tensile tests were performed in three different rolling directions to determine the mechanical properties of the materials. To evaluate the resistance of the materials to edge cracking, Hole Expansion (HE) tests were conducted. As a result of the improvements and analyses made by replacing the 600DU material with a thickness of 1.2mm with cold-rolled 800DU material with a thickness of 1.0mm, the proposed application appears feasible for the part geometry under consideration.
26 September 2025 in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
Recent advancements in the automotive industry have emphasized the importance of fuel efficiency, weight reduction, and durability. In response, AHSS materials have become widely used, particularly in cold forming. However, their high strength reduces formability, leading to challenges such as edge cracking. In this study, 600DU steel from two different mills was tested. Tensile tests were conducted on EU1 and EU2 at 0°, 45°, and 90° to the rolling direction per JIS Z 2241 No. 5. The tensile strength values were similar, but EU2 showed higher elongation. A hole expansion test revealed an average expansion of ~27% for EU1 and ~60% for EU2. Vickers hardness was measured under an HV 10 load. Metallographic preparation was followed by microstructural analysis using optical and SEM microscopy. In the AutoForm simulation analysis, the average thickness reduction of the EU1 steel was determined to be 19%, while that of the EU2 steel was measured at 11%. These results indicate that the EU1 steel exhibits 8% greater thinning compared to the EU2 steel. This study examines the formability of 600DU (dual-phase) AHSS steel from different manufacturers using numerical and experimental methods. The findings provide key insights into AHSS forming performance and help address potential issues. Numerical and experimental data modeling will contribute to optimizing manufacturing processes.