Ni-Hard cast iron materials are frequently used in equipment where high wear resistance is required in industrial applications. Generally, Ni-Hard is produced by conventional casting techniques. In this study, it was aimed to produce Ni-Hard powders to produce Ni-Hard cast iron materials with additive manufacturing techniques. To produce spherical and fine raw materials for additive manufacturing techniques, the gas atomization technique with a close-coupled nozzle system was preferred for the production of Ni-Hard powders. Ni-Hard alloy was melted in a high-frequency 10kW induction furnace under a protective atmosphere integrated into the gas atomization system. During the atomization process, 150 °C superheating was applied to prevent the liquid metal from freezing and clogging the melt delivery tube. In terms of the continuity of the atomization process, the negative pressure (aspiration pressure) values formed at the end of the melt delivery tube at different gas pressures were measured. An aspiration pressure of -50 mbar was obtained under an atomization pressure of 35 bar. Particle size distributions, hall flow behaviour and angle of repose properties of the produced powders were determined. Finally, the characterization of the powders was carried out by scanning electron microscopy. It was determined that the powders obtained as a result of atomization exhibited a spherical morphology and a narrow size range. The Hall flow rate test result of Ni-Hard powders was measured as 22 seconds for 50 g.
30 December 2021 in SDÜ Fen Bilimleri Enstitüsü Dergisi
Alüminyum ve alaşımları düşük yoğunluk, yüksek spesifik mukavemet, korozyon dayanımı, yüksek elektriksel ve ısıl iletkenlik özelliklerinden dolayı otomotiv, havacılık ve uzay, savunma sanayilerinde yaygın olarak kullanılmaktadırlar. Genellikle malzemelerin mukavemetlerinin artırılması bakımından, alüminyum alaşımlarında ısıl işlem ve deformasyon prosesleri uygulanmaktadır. Magnezyum ve bakır alaşım elementlerinin ilavesi ile alüminyum alaşımlarında kayda değer bir mukavemet artışı sağlanabilmektedir. Malzemelerin özellikleri; malzemelerin kimyasal kompozisyonlarına, proseslerine ve mikroyapılarına bağlı olarak değişmektedir. Bu modelleme ve simülasyon çalışmasında, Al-10Si-xMg alaşımında değişen % ağırlıkça Mg oranlarının malzeme üzerindeki etkisi incelenmiş ve CALPHAD metodolojisinin kullanımı ile termodinamik analizleri gerçekleştirilmiştir. Modelleme ve simülasyon çalışmalarında Thermo-Calc yazılımı 2021a versiyonundaki TCAL7.1 alüminyum veri tabanı kullanılmıştır. Al-10Si-xMg alaşımında değişen % ağırlıkça Mg oranının liküdüs, solidüs ve Al-Si alaşımlarında görülen ötektik reaksiyon sıcaklıklarına etkisi incelenmiştir. Ayrıca ısıl işlem ile mukavemet artışı sağlayan Mg2Si çökeltilerinin oluşum sıcaklıkları ve miktarları belirlenerek Türkçe literatüre katkı sağlanması düşünülmüştür.
25 April 2023 in SDÜ Fen Bilimleri Enstitüsü Dergisi
Dual phase (DP) steels are rapidly becoming more and more popular for automotive applications. They offer a weight reduction with a combination of energy absorption for crash zones. Rails, reinforcements, back panels, cross members, and pillars can be given as application examples. DP steels microstructure consists of a soft ferrite matrix with hard martensite islands. The hard martensite islands provide strength while the ductile ferrite provides formability. The strength level of DP steel is related to the amount of martensite in the microstructure, and the martensite amount can be arranged via intercritical annealing. In this work, thermodynamic analysis of St52 steel was carried out with Thermo-Calc software. A1 and A3 temperatures were determined by calculating the temperature-dependent phase fractions. Intercritical annealing temperatures were determined according to the calculated critical temperatures (A1 and A3). The intercritical annealing process was modelled by using Simheat NxT software. In this modelling and simulation work, the effect of intercritical annealing temperature on the final microstructure and hardness of DP steel was investigated.
1 March 2023 in Konya Journal of Engineering Sciences
As a material forming method, cold forging is preferred due to the reasons like absence of a heating step and high surface quality. Recently, the finite element method (FEM) has received growing attention for controlling and predicting final material properties for cold forging applications. FEM combines microstructure evolution models with failure criteria, thus providing solutions to complicated problems in the modern cold forging industry. The fastener industry extensively utilizes cold forging, in which manganese and boron-containing steels like 27MnB4 can be formed to obtain high mechanical properties. The current study investigates the effect of two different heat treatments, namely softening and spheroidizing annealing, on the formability of 27MnB4 bolts. Softwares such as Thermo-Calc 2022a and Forge NxT 3.2 were used to predict the microstructure of the wire rod and evaluate the cold forming process of the same rod under two different heat treatment conditions. Therefore, the current study also provides a relationship between microstructural features and the cold formability of 27MnB4 steel. The microstructure of 27MnB4 is predicted by CCT diagrams. The predicted microstructure corresponds to the microstructure of 27MnB4 samples taken from the production line. In addition, temperature, von Mises stress, and equivalent strain distributions for 27MnB4 steel in the hot rolled state were calculated higher than in annealed states due to the differences in the microstructure. These results demonstrate that computational material engineering methods and simulation techniques could be practical tools for cold forming processes.
Severe wear is a frequent cause of failure in industrial machinery that lacks adequate surface protection. Iron-based alloys offer an attractive combination of hardness, fracture toughness, and low cost for addressing this problem. In this study, a CALPHAD-based thermodynamic approach was employed to design a novel Fe-M(Nb,Mo,Cr)-C-B alloy, which was cast and subsequently processed into powders by gas atomization. The powders showed a Hall flow rate of 27 s/50 g and an angle of repose of 26°. The alloy composition was determined by optical emission spectroscopy, X-ray fluorescence (Nb), and inductively coupled plasma mass spectrometry (B), while X-ray diffraction confirmed the presence of α-iron and complex borocarbide phases. SEM/EDS analysis revealed a spherical powder morphology and a refined, uniformly distributed borocarbide microstructure induced by rapid solidification. Electron backscatter diffraction indicated a near-random crystallographic texture, and grain orientation spread maps revealed increasing internal strain with decreasing particle size. Nanoindentation gave localized hardness values of approximately 1330–1590 HV0.0005, which decreased with increasing particle size. The refined borocarbide-reinforced microstructure, high localized hardness, and good flowability suggest that the developed powder is a candidate feedstock for wear-resistant coating applications, although its coating and wear performance remain to be verified.