Chunrong Jiang

Chunrong Jiang

Auto-generated profile, based on publicly available information

Chunrong Jiang

School of Electric Power Engineering, Nanjing Institute of Technology, Nanjing 211167, China

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2021 in Ultrasonics
Verified
Journal Article
Closed access
CJChunrong Jiang
Chunrong Jiang
XWXinyu Wu
Xinyu Wu
DLDanhong Lu
Danhong Lu
ZXZhike Xu
Zhike Xu
LJLong Jin
Long Jin

21 September 2022 in Ultrasonics
Verified
Journal Article
Closed access
CJChunrong Jiang
Chunrong Jiang
ZZZilong Zhao
Zilong Zhao
DLDanhong Lu
Danhong Lu
ZXZhike Xu
Zhike Xu
LJLong Jin
Long Jin

1 January 2018 in Ultrasonics
Verified
Journal Article
Closed access
XDXiaoxiao Dong
Xiaoxiao Dong
MHMinqiang Hu
Minqiang Hu
LJLong Jin
Long Jin
ZXZhike Xu
Zhike Xu
CJChunrong Jiang
Chunrong Jiang

5 October 2020 in IEEE Access
Verified
Journal Article
Open access
XDXiaoxiao Dong
Xiaoxiao Dong
Kenji UchinoKenji Uchino
Kenji Uchino
CJChunrong Jiang
Chunrong Jiang
LJLong Jin
Long Jin
ZXZhike Xu
Zhike Xu
YYYue Yuan
Yue Yuan
Heat generation by internal loss factors of piezoelectrics is one of the critical issues for high power density piezoelectric applications, such as ultrasonic motors, piezoelectric actuators and transducers. There are three types of internal losses in piezoelectric materials, namely dielectric, elastic and piezoelectric losses. In this paper, a decoupled equivalent circuit is proposed to emulate a piezoelectric disk in radial vibration mode considering all three types of internal losses. First, the decoupled equivalent circuit is derived according to the conventional electromechanical equivalent circuit model. Then, a piezoelectric disk configuration in radial vibration mode is explored and simulated. The resonance and antiresonance frequencies and their corresponding mechanical quality factors are achieved by the proposed circuit. In order to verify the accuracy of the simulation results, the piezoelectric disk is fabricated and tested. Simulation results with the new circuit exhibit a good agreement with experimental results. Finally, the equivalent circuit with only dielectric and elastic losses are simulated and compared which further validates the accuracy improvement of the new equivalent circuit considering all three losses.

6 March 2020 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
XDXiaoxiao Dong
Xiaoxiao Dong
CJChunrong Jiang
Chunrong Jiang
LJLong Jin
Long Jin
ZXZhike Xu
Zhike Xu
YYYue Yuan
Yue Yuan
High-efficiency energy conversion, primarily limited by internal losses of piezoelectric materials, is an important target for piezoelectric actuators or sensors. There are three internal losses in piezoelectric materials: dielectric, elastic, and piezoelectric. In this article, a new equivalent circuit of a piezoelectric ring in radial vibration mode is proposed considering three types of fundamental losses. First, the decoupled equivalent circuit with inherent losses is derived based on the conventional electromechanical equivalent circuit. In order to verify the feasibility of the new circuit, an ultrasonic motor operating in radial vibration mode is explored and simulated. The resonance and antiresonance frequencies and their corresponding mechanical quality factors are obtained from the new circuits and then compared with those of an actual stator sample. The simulation results match well with the experimental measurements of the stator. Finally, a prototype is fabricated due to the simulation results and a maximum torque of 270 mNm is acquired.

1 January 2019 in Mathematical Problems in Engineering
Verified
Journal Article
Open access
PDF file
CJChunrong Jiang
Chunrong Jiang
XDXiaoxiao Dong
Xiaoxiao Dong
LJLong Jin
Long Jin
DLDanhong Lu
Danhong Lu
The focus of this paper is to propose a contact model of a radial standing wave ultrasonic motor in order to evaluate the motor performance accurately. The contact behavior between the stator and rotor is characterized by test and a continuous contact on the contact interface is confirmed. A contact model describing the continuous contact is then developed with analytical method. The stator vibration, the force transmission between the stator and rotor, and the output of the motor are analyzed. The impacts of different vibration amplitudes and structural parameters on the performances of the motor are evaluated based on the proposed model. Finally, a test platform for measuring the performance of the motor is built and torque‐speed curves of the motor under different voltages are measured. The accuracy of the contact model is verified by comparison between measurement and calculation results. The proposed model not only can be used for design and optimization of the radial standing wave ultrasonic motor but also offers insight into the contact mechanics of standing wave ultrasonic motors.