Technical University of Munich, School of Engineering and Design, Department of Energy and Process Engineering, Chair of Electrical Energy Storage Technology, 80333 Munich, Germany
Auto-generated profile, based on publicly available information
Alexander Frank
Technical University of Munich, School of Engineering and Design, Department of Energy and Process Engineering, Chair of Electrical Energy Storage Technology, 80333 Munich, Germany
Cylindrical formats for high energy lithium-ion batteries shifted from 18650 to 21700 types offering higher volumetric energy density and lower manufacturing costs. Bigger formats such as 26650 may be of benefit as well, but longer electrodes and increased heat accumulation due to larger cell diameters are challenging for the batterys design and performance. An experimental review of state-of-the-art cylindrical lithium-ion batteries implies a delayed development of high energy 26650 cells. Optimized and prospective tab designs are discussed for high energy 18650, 21700 and 26650 formats using an experimentally-validated multi-dimensional multiphysics model of a silicon-graphite/nickel-rich lithium-ion battery. The model incorporates several 1D electrochemical models combined with a 2D electrical and a 3D thermal model. Novel in- and through-plane voltage-drop analysis reveals a dominant influence of the tab design on the cells total polarization, where a multi-tab instead of a single-tab design can improve the fast charging efficiency by up to +23% SoC. Fast charging profiles are adapted to tab design and cylindrical format, which prevent overheatings and the local onset of lithium plating across the active electrode area. Multi-tab design is recommended for high energy 26650 cells, but imbalances in SoC and temperature suggest alternative formats at slightly reduced cell diameters.
23 September 2019 in Journal of the Electrochemical Society
The energy density of lithium-ion batteries can be enhanced by using thicker and denser electrodes, which leads to transport limitations in the electrolyte within the porous structures. A pore morphology modification of the electrodes can counteract this limitation mechanism and provide higher rate capabilities of the cells. In this work, graphite anodes are structured with a picosecond laser in order to create transport pathways for the lithium-ions and allow for enhanced penetration of the electrodes. Experimental data from graphite/NMC-111 coin cells with varying areal capacities are used for the development and parameterization of an electrochemical model. The modified pore morphology of the structured electrodes is represented in the model by an adapted tortuosity, which results in lower lithium-ion concentration gradients and reduced diffusion polarization in the electrolyte. The effect of electrode thickness and tortuosity on limiting mechanisms is analyzed via simulation studies in order to derive the impact of structured electrodes. As a result, improved discharge as well as charge rate capability appears beside enhanced safety features such as increased tolerance versus hazardous lithium-plating during fast charging scenarios.
The 18 650 and 21 700 cell format are state of the art for high-energy cylindrical lithium-ion batteries, while Tesla proposed the new 4680 format with a continuous ”tabless” design as the choice for electric vehicle applications. Using an experimentally validated multidimensional multiphysics model describing a high energy NMC811/Si-C cylindrical lithium-ion battery, the effects of tabless design and cooling topologies are evaluated for 18 650, 21 700, and 4680 cell formats under varying charging protocols. Mantle cooling is found to be the most efficient cooling topology for a segmented tab design, whereas tab cooling performs equally well for tabless cells and achieves better performance for the 4680 format. By massively reducing polarization drops (approx. 250 mV at 3C) and heat generation inside the current collectors (up to 99%), the tabless design increases cell homogeneity and enables format-independent scalability of fast-charging performance with a tab-cooling topology. In addition, the 0 to 0.8 SoC charge time can be reduced by 4 to 10 min compared to cells with a segmented tab design, resulting in 16.2 min for the 18 650 and 21 700, and 16.5 min for the larger 4680 cell format.
1 May 2024 in Journal of the Electrochemical Society
The anode overhang is usually cited to prevent lithium plating at the cell edges of lithium-ion batteries. Still, numerous reports in the literature show lithium plating at the cell edge, which is typically referred to as edge plating. Edge plating is often attributed to inhomogeneous lithium distribution, thermal gradients, or pressure-dependent effects. This work presents an easy-to-implement two-dimensional electrochemical model demonstrating inhomogeneous lithiation induced by the anode overhang, which can explain experimentally observed edge plating. First, the mechanism of inhomogeneous lithiation due to the anode overhang is explained in detail. Then, a parameter study on charge protocol and geometric cell properties is presented, and the implications for cell applications are analyzed. Finally, the findings are discussed and put into a broader perspective of cell design, manufacturing, and fast charging application. In Part II of this work, the simulation is validated experimentally using multi-reference electrode single-layer pouch cells.
3 October 2019 in Journal of the Electrochemical Society
A multidimensional multiphysics model is presented to describe the external short circuit behavior of lithium-ion cells of various formats and sizes at different convective cooling conditions. For this purpose, a previously published homogenized physical-chemical model of the external short circuit behavior of a small-sized lithium-ion cell was combined with an electrical and a thermal model to describe in-plane inhomogeneities in current density and heat generation rate throughout the electrodes, together with the resulting temperature distribution within the cell’s jelly roll or electrode stack. With the investigated cylindrical, prismatic, and pouch-type cell formats combined with cell capacities ranging from consumer-sized to automotive applications, a comprehensive cell design study is presented during external short circuits. The investigated surface and tab cooling strategies reveal a limited cooling capability of each cell format and size, which seems to be defined by the ratio of cooled surface area to electrode area as well as the thermal resistivity of the respective cell geometry. The simulation results show that only thin cells with a large ratio of cooling surface to electrode area can be physically maintained within an uncritical operating window of cell temperature and state of charge in case a low-resistance external short circuit is applied.