14 November 2022 in International Transactions on Electrical Energy Systems
PCPazhanimuthu Cholamuthu
BIBaranilingesan Irusappan
+3
The current needs of more nonlinear loads and the frequent usage of single-phase loads in three-phase system drastically create power quality issues in the grid-connected system. As a consequence, it creates an undesirable power quality issue (PQI) in the form of a change in the nature of voltage and current magnitude and waveforms in the power system. The voltage-related PQI leads to a huge disturbance in the system when compared with the current-related PQI. The hybrid series active power filter provides grids with the required voltage in series and suppresses the voltage-related harmonics caused by grid-connected nonlinear loads. The present work deals with an adaptive neurofuzzy inference system controller for the generation of a reference voltage signal that uses a reduced active filter rating. The simulation study was done in the MATLAB 2020b/Simulink environment and the experimental effectiveness of the proposed ANFIS controller was compared with that of a conventional controller. In the grid-connected system, this system prevents voltage quality problems such as voltage sag, flickering, voltage swell, neutral currents, and reactive power. The renewable energy sources interfaced into the DC-link minimize short and long voltage challenges so that they improve the overall performance of the system. In accordance with IEEE standard 519-1992, a prototype model was proved to demonstrate that the power delivery system works effectively under different conditions and reduces the total harmonic distortion by approximately 30%, which is less than the 5% acceptable limit.
27 March 2024 in e-Prime - Advances in Electrical Engineering, Electronics and Energy
7 October 2021 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
A new topology of photovoltaic (PV) based transformerless dynamic voltage restorer (TDVR) with high gain DC-DC boost converter is proposed to mitigate voltage sag and swell, interruptions, and unbalanced outages in single-phase grid. The proposed PV-DVR high DC-DC boost converter is comprised of one MOSFET switch and three inductors with second order generalized integrator (SOGI) based unit vector template (UVT) control to enhance the effectiveness of the system for grid-connected renewable applications. The high voltage (HV) gain is achieved by this proposed converter through its soft-switching ability and coupled inductor arrangement with continuous conduction mode (CCM). In the proposed high gain DC-DC converter, the MOSFET IRFP260 power switch is preferably used for low voltage stress and also minimum on-state resistance. The mathematical analysis of the proposed converter is also discussed in this paper. The proposed converter is interfaced with an SOGI-PLL controller with input voltage (24 V), output voltage (230 V), and power rating as 250 W with less number of both passive and active switches. Moreover, to validate the performance and advantage of the proposed converter, the system was simulated by using MATLAB-SIMULINK and laboratory 250 W prototype results are presented to show the effectiveness of the design to limit the voltage sag – 0.1 pu and swell – 1.9 pu and also THD% level within in ceiling limit prescribed in IEEE STD at the load side.
21 August 2021 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
KSKishor Kumar Sadasivuni
Traditionally the grid supplies only a particular voltage to the load, but today we are using ‘n’ number of loads with different voltage rating and converters. So, the conversion of the generated AC voltage into several stages of DC voltage before reaching the load is required. In this paper, the Multi Port Converter (MPC) is proposed, which is capable of converting a single valued AC voltage into several stages of DC voltage. The feasibility of employing of converter level switch node, as an interface to numerous output stages is examined in this paper. The connecting of several outputs at the identical node is accomplished by the use of time-division multiplexing technique. In this study, the input power is multiplexed into separate ports via a phenomenon known as Switching Boost Action (SBA). The prototype was developed for converting the 240 V, 50 Hz, single phase AC supply into two outputs and the 12 V DC supply which can fed to the loads, that can be stored in batteries for future use. This paper has been proposed to design SBA based MPC using dsPIC controller for renewable energy applications.
21 December 2021 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Due to advancements in power electronics devices and the support of improvements on both the power supply and load sides, Distributed Energy (DG) is rapidly being connected to the grid in the form of AC/DC Hybrid Micro-Grid (HMG). The development will result in a substantial change in the network topology, new design problems for the micro-grid control unit, and new requirements for the simulation testing laboratory. The Bidirectional AC-DC converter (BAC) is necessary for hybrid microgrids to provide voltage stableness and power equilibrium between the AC and DC grids. To suppress the harmonic current control approach, an enhanced Fryze-Buchholz Depenbrock (FBD) current harmonic detection technique is integrated with droop control in this paper. This proposed system not only performs the power transformation but also minimizes harmonics. While considering non-linear load, the proposed system yields the control ability for regulating the converter to eliminate the harmonics of 74.41% in the grid current. While incorporating the HMG in the proposed system, the control strategy decreases 90.3% and 89.4% of reactive power in both linear and non-linear loads. The obtained simulation results are used to confirm the feasibility and effectiveness of the control scheme.
5 September 2022 in International Transactions on Electrical Energy Systems
Concerns about pollution, climate change, limited fossil fuel supplies, and the desire to eliminate energy dependency have sparked a surge in interest in electric vehicles (EVs). EV requirements have resulted in a variety of difficulties and remedies in EV technology. One of them is the use of DC-DC converters to transfer the level of voltage from the battery in an EV to other needed voltage levels. An independent converter for each operating voltage might be used as a remedy. On the other hand, single input multiple output (SIMO) converters can be utilized to decrease costs, reduce switching loss, and thus enhance the system efficiency. In this paper, a nonisolated step-up converter with the integration of the Luo network is proposed for multiple outputs (24 V and 48 V). In electric vehicles, 48 V is utilized for battery backup, while 24 V is utilized for the horns, headlights, telematics, or the microcontroller. The experimental observations of a 36 V, 600 mA, 24 W prototype confirm the theoretic examination and demonstrate the advantages of the proposed converter over other multioutput converters. The STM microcontroller, based on an ARM cortex microprocessor, is linked into the Luo network for making pulses. The proposed converter achieves 94.2% efficiency at full power. The proposed converter’s performance is evaluated through MATLAB/SIMULINK software, and the results are validated experimentally.