23 October 2023 in IEEE Transactions on Antennas and Propagation
In this communication, a compact end-fire circularly polarized (CP) antenna designed for satellite communication on mobile terminals is proposed. In our design, a rectangular loop antenna is proposed with a compressed vertical dimension which is suitable to be integrated into the plastic bezel of the mobile terminals. The folded dipole mode and loop mode of the rectangular loop antenna provide orthogonal radiation components. An L-shaped stub is introduced to excite the two modes by capacitive coupling. The directivity of the horizontally polarized (HP) radiation is improved to be comparable to that of the vertically polarized (VP) radiation when integrating with the chassis ground. Independent mode tuning can be achieved with capacitive loading on the antenna. A prototype was fabricated to validate the design. The measured results indicate that a -6 dB impedance bandwidth of 10.0%, axial ratio (AR) bandwidth of 0.76% (covering the S band of the BeiDou Navigation Satellite System (BDS) of 2483.5 ~ 2500 MHz), and a peak gain of 4.80 dBic are achieved with a compact size of 0.47λ 0 × 0.06λ 0 × 0.004λ 0 . The proposed CP antenna has the merits of compact size, improved gain, and quasi-planar structure which is a good candidate for mobile terminals supporting satellite communication.
14 November 2022 in IEEE Transactions on Antennas and Propagation
In this paper, a mechanically reconfigurable 1-D reflectarray actuated by a single motor is proposed. The elements are designed as metal tubes that are lifted by the ejectors. To achieve continuous phase growth in a limited space, the discontinuity of the Archimedean spiral is utilized. Then, a novel drive mechanism is constructed to transfer the power of the motor to each element. The combination of the Archimedean spiral cam and the follower effectively converts the rotation of the shafts to the linear motion of the element. In conjunction with the timing pulleys and timing belts, the Archimedean spiral cams generate a periodic changing phase gradient over time. The whole structure is supported by low-cost acrylic plates with fasteners. The main parts are composed of standard components and the overall structure is easy to realize. The reflectarray at normal incidence offers a beam steering range from -60° to 60° in one dimension at 5 GHz. The beam coverage test demonstrates a maximum improvement in the received signal level of 16 dB in the multipath environment. This work provides a new solution to the design of mechanically reconfigurable reflectarrays.
12 April 2023 in IEEE Transactions on Antennas and Propagation
In this communication, a 360° azimuth scanning array based on a compact reconfigurable element is proposed for aviation applications. In our design, a reconfigurable compact Yagi-Uda element is constructed by combing a driven element and two switchable parasitic elements. When constituting an array, more energy can be coupled to the parasitic elements and the current magnitude of the parasitic element reaches nearly the same as that of the driven element. Then, a tunable backside radiation zero point and high backside suppression can be realized for the Yagi-Uda element with only one reflector. The reconfigurable element is able to switch the radiation pattern between two broadside states in two directions and an endfire state. The measured results of the 1 × 8 prototype indicate that a wide scanning range from -180° to 180° is attained with a peak gain of 11.8 dBi and a gain fluctuation of less than 3 dB. The array has a small cross-section area of 0.47λ 0 × 0.26λ 0 . This work provides a compact reconfigurable antenna with full 360° coverage for aviation applications. The tunable radiation zero point has the potential to promote future anti-interference array designs.
18 July 2024 in IEEE Transactions on Antennas and Propagation
In this paper, a novel decoupling scheme based on active impedance matching is proposed for the decoupling of axial symmetrical three antennas. Three simultaneous excitation modes with the same amplitude and different phase relationships are utilized to analyze the decoupling problem. In the perspective of simultaneous excitations, the decoupling of the three antenans can be transformed into active impedance matching. Theoretical demonstration reveals that achieving decoupling for axial symmetrical three antennas necessitates matching the active impedances under the three excitations. The active impedance matching can be solved intuitively in a clear step-by-step process by exploiting the impedance characteristics of the coupled three-line and the unique field distribution under different excitation modes. To validate the effectiveness of the proposed method, the decoupling of axial symmetric three inverted-F antennas (IFAs) is presented as an example. The achieved isolation exceeds 17 dB in the desired band with a peak isolation of 31 dB. With good isolation and a straightforward design process, the approach holds promise for future multi-input multi-output (MIMO) antenna systems. Furthermore, the proposed method provides a new physical intuition for solving the decoupling problem of multiple antennas without the need for numerous optimizations.
16 July 2025 in IEEE Transactions on Antennas and Propagation
In this paper, we propose a simple scheme for dual-band antenna decoupling utilizing parallel LC resonators. By leveraging the common mode and differential mode (CM/DM) S-parameters, we provide a convenient method for distinguishing the coupling characteristics between the antennas. Based on this approach, we show that the dual-band PIFAs operating in the TM0,0.5 and TM1,0.5 modes exhibit electric and magnetic coupling in the respective frequency bands. The decoupling of these two bands can be achieved in a methodological way using the inductance of the parallel LC resonator below the resonant frequency and the capacitance above the resonant frequency. Decoupling for different frequency ratios can be readily adjusted by modifying the impedance characteristics of the LC resonator. By controlling the relative positions of the LC resonators, separate adjustments of decoupling in the two bands can be accomplished, thereby simplifying the decoupling process. To validate the effectiveness of the proposed method, a prototype is fabricated. The measured results demonstrated that the proposed scheme achieves effective isolation enhancement from 5 dB to 14 dB and 9 dB to 15 dB in two frequency bands, respectively. The proposed decoupling scheme offers a simple and efficient decoupling process with an easily realizable structure, making it a promising solution for future MIMO system designs.
1 January 2026 in IEEE Antennas and Wireless Propagation Letters