9 November 2018 in IEEE Transactions on Antennas and Propagation
This paper presents a novel high-gain endfire slot antenna array fed by air-substrate microstrip line. It has a simple and compact structure consisting of a copper strip and two copper sheets. Designed based on the slot antenna array, the antenna could be embedded into a large metallic platform. The surface wave above the antenna radiates the energy to free space. Fed by the air-substrate microstrip line, the antenna works on the TEM mode. Therefore, the antenna obtains a suitable phase constant to realize stable endfire radiation pattern and could be designed by a long structure to realize high endfire gain. Because all of the antenna is designed by metal, it has the characteristic of high strength, easy fabrication and low cost. With the radiated aperture of 3.5 wavelength, the antenna achieves a measured endfire gain of 11.81 dBi. The measured 1-dB gain and 3-dB gain bandwidths reach 4.5% and 8.4%, respectively. Good matching and a stable endfire radiation pattern are obtained over the entire operating band from 3.75 to 4.15 GHz.
31 January 2018 in IEEE Antennas and Wireless Propagation Letters
The expansion of a hybrid genetic programming (GP) for the development of broadband 2D metamaterial designs with advanced characteristics is presented. Artificial magnetic conductor (AMC) ground planes and tunable terahertz (THz) absorbers generated by the hybrid GP are compared with designs available in literature. The hybrid GP is shown to produce human-competitive results. The AMC ground planes synthesized by the hybrid GP produce improved results including wider bandwidths and larger reflection coefficient magnitudes than that of the human designs. For one of the designed AMCs, the hybrid GP's bandwidth is 73.3% larger and the minimum reflection magnitude is 1.0% larger than the reference AMC. Similarly, the absorber synthesized by the hybrid GP has larger bandwidths than that of a recently published absorber optimized by random hill climbing. Three bias voltages were tested with the tunable absorber. The bandwidths of the hybrid GP absorber are 23.1%, 37.6%, and 400% larger than the reference absorber, for biases of 4, 2, and 0.5 V/nm, respectively. Four example designs are discussed together with comparative results to illustrate the advantages of the developed GP enabled design method.
16 January 2014 in IEEE Transactions on Antennas and Propagation
This communication proposes a dual-polarized slot antenna array, which is able to expand two-dimensionally (2-D), using only one layer of substrate board. Two identical coplanar waveguide (CPW) series-fed slot arrays are positioned orthogonally, providing dual polarization with high port isolation. The overall array is arranged on both sides of a single substrate, achieving low cost in fabrication. To validate the design concept, a model of the proposed array is built for the 2.4-GHz wireless local area network (WLAN) application. We have measured S parameters, radiation patterns and gain, and compared them with the simulation results.
9 October 2018 in IEEE Transactions on Antennas and Propagation
This communication presents a microstrip-fed surface wave antenna for endfire radiation. The antenna has the advantage of high endfire gain, wide endfire gain bandwidth and stable endfire radiation pattern. It consists of a microstrip line with air media and a dielectric cuboid. The half-mode dielectric waveguide, which is made up by the dielectric cuboid and the air substrate introduced by the microstrip line, is the radiating structure of the antenna. Fed by a microstrip line, the half-mode dielectric waveguide couples the energy continuously with a moderate phase constant, which is helpful for the antenna to realize a high endfire gain and a stable endfire radiation pattern. With a low dielectric constant, the half-mode dielectric waveguide has a stable radiation performance within a wide bandwidth. With a length of 5.76 wavelength, the antenna achieves a maximum endfire gain of 13.3 dBi at 4.75 GHz. The 1-dB gain and 3-dB gain bandwidths of the antenna is 18.1% and 37.8%, respectively. Good matching is obtained from 3 to 6.5 GHz.
14 November 2022 in IEEE Transactions on Antennas and Propagation
In this paper, a mechanically reconfigurable 1-D reflectarray actuated by a single motor is proposed. The elements are designed as metal tubes that are lifted by the ejectors. To achieve continuous phase growth in a limited space, the discontinuity of the Archimedean spiral is utilized. Then, a novel drive mechanism is constructed to transfer the power of the motor to each element. The combination of the Archimedean spiral cam and the follower effectively converts the rotation of the shafts to the linear motion of the element. In conjunction with the timing pulleys and timing belts, the Archimedean spiral cams generate a periodic changing phase gradient over time. The whole structure is supported by low-cost acrylic plates with fasteners. The main parts are composed of standard components and the overall structure is easy to realize. The reflectarray at normal incidence offers a beam steering range from -60° to 60° in one dimension at 5 GHz. The beam coverage test demonstrates a maximum improvement in the received signal level of 16 dB in the multipath environment. This work provides a new solution to the design of mechanically reconfigurable reflectarrays.
5 December 2016 in IEEE Transactions on Antennas and Propagation
A new antenna structure is proposed to show that a single-layer magnetic current array based on the microstrip line structure can achieve a relatively uniform and large in-phase radiating aperture together with high realized aperture usage rate (RAUR). By alternatively and periodically loading the microstrip line with blocking stubs, the equivalent magnetic currents along one direction are suppressed while the currents along the other direction are left, forming a relatively uniform and in-phase 1-D magnetic current array. The electromagnetic wave is radiated into space while traveling forward along the line. By in-parallel concatenating a series of the 1-D arrays with adjacent arrays presenting mirror relations, a large in-phase radiating aperture is built with a relatively high RAUR performance. Moreover, the shorting walls at the interconnecting planes of the neighboring 1-Darrays can be removed attributing to the antenna arrangement style and the required feed network. Eight rows of the 24-element 1-D magnetic current array fed using a substrate integrated waveguide-based eight-way power divider fabricated using a single substrate board is simulated and built to demonstrate the design strategy. The prototype shows a measured bandwidth of 4.37% and a peak gain of 25.1 dBi at 20 GHz. The RAUR is 8.66/λ 0 2 , which is higher than most of the single-layer high-gain antennas.