26 March 2024 in Chemnanomat
High entropy alloys (HEAs) have a wide range of applications across various fields, including structural engineering, biomedical science, catalysis, magnetism, and nuclear technology. Nanoscale HEA particles show promising catalytic properties. Nevertheless, attaining versatile composition control in nanoparticles poses a persistent challenge. This study proposes the use of pulsed laser ablation in liquids (PLAL) for synthesizing nanoparticles using equiatomic CoCrFeMnNi targets with varied preparation methods. We evaluate the impact of target preparation method on nanoparticle yield and composition as well as the magnetic properties of the nanoparticles. The elemental powder‐pressed heat‐treated target (HEA‐PP), identified as the most time‐efficient and cost‐effective, exhibits noticeable segregation and non‐uniform elemental distribution compared to ball milled hot‐pressed powder (HEA‐BP) and face‐centered cubic (FCC) single crystal (HEA‐SX) alloy targets. From all targets, nanoparticles (sizes from 2 to 120 nm) can be produced in ethanol with a nearly equiatomic CoCrFeMnNi composition and a FCC structure, showing oxidation of up to 20 at.%. Nanoparticles from HEA‐PP exist in a solid solution state, while those from HEA‐BP and HEA‐SX form core‐shell structures with a Mn shell due to inhomogeneous material expulsion, confirmed by mass spectrometry. HEA‐PP PLAL synthesis demonstrates 6.8 % and 15.1 % higher productivity compared to HEA‐BP and HEA‐SX, establishing PLAL of elemental powder‐pressed targets as a reliable, time‐efficient, and cost‐effective method for generating solid solution HEA nanoparticles.
25 March 2025 in Beilstein Journal of Nanotechnology
AAAbdel Rahman Altakroury
+4
The potential to modify the size distribution of nanoparticles synthesized by pulsed laser ablation in liquids is demonstrated using a donut-shaped laser beam. In experiments on pulsed laser ablation in water of gold, yttrium oxide, and high-entropy alloy targets with both Gaussian and donut-shaped beams, we observed a significant reduction in particle size, narrowing of the size distribution width, and an improvement in sphericity when utilizing the donut-shaped laser beam. We performed time-resolved shadowgraph imaging of the laser-induced cavitation bubble, revealing a toroidal structure that overruns the ring-shaped ablation site, compared to the quasi-hemispherical bubble covering the ablation spot produced by the Gaussian beam. Based on this pioneering study, further investigation with higher temporal and spatial resolution are warranted.
11 June 2018 in IEEE Transactions on Nuclear Science
In this paper, we present the first steps in the development of a new generation of ultrasonic sensors devoted to fission gas characterization in a material testing reactor harsh environment. The piezoelectric active material is a sodium bismuth titanate thick film fabricated using a screen-printing method. Characterization of piezoelectric and dielectric properties and material parameter studies based on temperature were carried out. The key results of this paper are demonstrated and discussed in terms of feasibility for application to a new sensor device operating at high temperature (350 °C). An acoustic test in a cylindrical cavity shows high sensitivity to measurements of liquid substances at room temperature. To verify its applicability to gas detection, a theoretical model based on electromechanical properties and impedance matching equations was introduced. This model was used in the studies on gas measurement under room temperature and at 350 °C. It was theoretically shown that the sensor was able to operate for gas in situ under harsh temperature conditions.
12 November 2026 in Beilstein Journal of Nanotechnology
AAAbdel Rahman Altakroury
Pulsed laser ablation in liquids (PLAL) is a versatile and sustainable technique for the synthesis of ligand-free colloidal nanoparticles, but its wider application is limited by relatively low productivity and insufficient control over particle size distributions. Here, to advance the technique, we investigate the possibility of combining in one synthesis process the advantages of two recently developed cost-effective approaches, multibeam PLAL for productivity increase and donut-shaped laser beams for particle size modification. Nanoparticles of gold, an iron–nickel alloy, and a high-entropy alloy were produced in water using single-beam and multibeam configurations with four and eleven picosecond sub-beams. The effects of beam profile, beam-splitting factor, and laser fluence on particle yield and size distributions were systematically evaluated. Splitting donut-shaped beams is shown to offer a similar productivity increase as Gaussian pulses, and, at moderate fluences, multiple donut beams can be even more efficient. A single donut-shaped beam generally reduces the particle size, but, in a multibeam configuration, the reduction effect is hindered by secondary processes such as the interaction of cavitation bubbles, nanoparticle fragmentation, and redeposition. The results demonstrate the feasibility of combining donut-shaped beams with multibeam ablation in PLAL synthesis and identify key process parameters that have to be optimized to achieve both high productivity and improved particle size control.
9 July 2026 in SSRN Electronic Journal
The optical emission in laser-induced breakdown spectroscopy (LIBS) is governed by the spatial intensity distribution of the incident laser beam, which influences plasma formation and evolution. Beam shaping therefore offers a route to control plasma dynamics and emission yield; however, its effects in LIBS remain insufficiently quantified, particularly under conditions relevant to compact instrumentation. In this work, a diffractive optical element (DOE) is used to transform a Gaussian beam into a 2×2 array, producing simultaneously expanding, co-propagating ablation plumes that interact during expansion. Plasma evolution from Cu and Si targets is investigated in vacuum using a Nd:YAG laser (1064 nm, 5 ns, 10 J cm-²), combining time-resolved imaging with optical emission spectroscopy. The multi-spot configuration results in enhanced emission intensity compared to single-spot irradiation, with increases of ~9 for Si and ~3 for Cu. The observed enhancement is attributed to plume–plume interaction effects that modify plasma density and emission characteristics. These results demonstrate that DOE-based beam shaping provides an effective and technically simple approach to increasing the LIBS signal without additional system complexity.
11 September 2026 in Beilstein Archives
AAAbdel Rahman Altakroury
Pulsed laser ablation in liquids (PLAL) is a versatile and sustainable technique for the synthesis of ligand-free colloidal nanoparticles, but its wider application is limited by relatively low productivity and insufficient control over particle size distributions. Here, to advance the technique, we investigate the possibility of combining in one synthesis process the advantages of two recently developed cost-effective approaches, multibeam PLAL for productivity increase and donut-shaped laser beams for particle size modification. Nanoparticles of gold, an iron-nickel alloy, and a high-entropy alloy were produced in water using single-beam and multibeam configurations with four and eleven picosecond sub-beams. The effects of beam profile, beam-splitting factor, and laser fluence on particle yield and size distributions were systematically evaluated. Splitting donut-shaped beams is shown to offer a similar productivity increase as Gaussian pulses, and, at moderate fluences, multiple donut beams can be even more efficient. A single donut-shaped beam generally reduces the particle size, but, in a multibeam configuration, the reduction effect is hindered by secondary processes such as the interaction of cavitation bubbles, nanoparticle fragmentation, and redeposition. The results demonstrate the feasibility of combining donut-shaped beams with multibeam ablation in PLAL synthesis and identify key process parameters that have to be optimized to achieve both high productivity and improved particle size control.