Arnob Ghosh

Arnob Ghosh

Auto-generated profile, based on publicly available information

Arnob Ghosh

Department of Electrical and Computer Engineering, The Ohio State University 1 , Columbus, Ohio 43210, USA

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 June 2020 in Journal of the Optical Society of America B
Verified
Journal Article
Closed access
AGArnob Ghosh
Arnob Ghosh
Shahriyar Safat DiptaShahriyar Safat Dipta
Shahriyar Safat Dipta
SNSk Shafaat Saud Nikor
Sk Shafaat Saud Nikor
NSNazmus Saqib
Nazmus Saqib
ASArnob Saha
Arnob Saha
SSSk Saud
Sk Saud
As poor stability is the primary constraint for the commercialization of perovskite solar cells, improving stability has been the primary focus of recent research works regarding solar cells that make use of perovskite materials. Different metal oxide transport layers are being used with the aim of fabricating stable perovskite solar cells. A stable and efficient solar cell with both metal oxide transport layers (ZnO and N i O X ) and a perovskite (methyl ammonium lead iodide) absorber layer is simulated in this work, and a comparison of performance parameters is made with other transport layers from the literature. The issue of optimization regarding the thickness of the absorber layer and the doping concentration in the absorber and transport layers has been addressed, and the effect of defect concentration at the interface has been investigated. Optimum performance is achieved with an absorber layer of thickness 800 nm. Linear grading is also introduced in the absorber layer by varying the concentration of different halides, which increases the efficiency by approximately 8% owing to the increase in the short circuit current density.

20 February 2023 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
AXAgnes Maneesha Dominic Merwin Xavier
Agnes Maneesha Dominic Merwin Xavier
AGArnob Ghosh
Arnob Ghosh
SRSheikh Ifatur Rahman
Sheikh Ifatur Rahman
AAAndrew Allerman
Andrew Allerman
SAShamsul Arafin
Shamsul Arafin
SRSiddharth Rajan
Siddharth Rajan
Ultra-violet (UV) light emitting diodes operating at 339 nm using transparent interband tunnel junctions are reported. Tunneling-based ultraviolet light emitting diodes were grown by plasma-assisted molecular beam epitaxy on 30% Al-content AlGaN layers. A low tunnel junction voltage drop is obtained through the use of compositionally graded n and p-type layers in the tunnel junction, which enhance hole density and tunneling rates. The transparent tunnel junction-based UV LED reported here show a low voltage drop of 5.55 V at 20 A/cm2 and an on-wafer external quantum efficiency of 1.02% at 80 A/cm2.

1 February 2024 in AIP Advances
Verified
Journal Article
Open access
PDF file
AGArnob Ghosh
Arnob Ghosh
KKKamruzzaman Khan
Kamruzzaman Khan
SSShrivatch Sankar
Shrivatch Sankar
ZJZhe (Ashley) Jian
Zhe (Ashley) Jian
SHSyed M. N. Hasan
Syed M. N. Hasan
SAShamsul Arafin
Shamsul Arafin
In this paper, we report the molecular beam epitaxy-grown InGaN-quantum disks embedded within selective area epitaxy of GaN nanowires with both Ga- and N-polarities. A detailed comparative analysis of these two types of nanostructures is also provided. Compared to Ga-polar nanowires, N-polar nanowires are found to exhibit a higher vertical growth rate, flatter top, and reduced lateral overgrowth. InGaN quantum disk-related optical emission is observed from nanowires with both polarities; however, the N-polar structures inherently emit at longer wavelengths due to higher indium incorporation. Considering that N-polar nanowires offer more compelling geometry control compared to Ga-polar ones, we focus on the theoretical analysis of only N-polar structures to realize high-performance quantum emitters. A single nanowire-level analysis was performed, and the effects of nanowire diameter, taper length, and angle on guided modes, light extraction, and far-field emission were investigated. These findings highlight the importance of tailoring nanowire geometry and eventually optimizing the growth processes of III-nitride nanostructures.

1 August 2024 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Open access
PDF file
AGArnob Ghosh
Arnob Ghosh
AXAgnes Maneesha Dominic Merwin Xavier
Agnes Maneesha Dominic Merwin Xavier
SRSiddharth Rajan
Siddharth Rajan
SAShamsul Arafin
Shamsul Arafin
We report a two-step etching process involving inductively coupled plasma (ICP) etching followed by wet chemical etching to achieve smooth and vertical sidewalls, being beneficial for AlGaN-based electronic and optoelectronic devices. The influence of ICP power on the roughness of etched sidewalls is investigated. It is observed that ICP etching alone does not produce smooth sidewalls, necessitating subsequent wet chemical etching using tetramethyl ammonium hydroxide (TMAH) to enhance sidewall smoothness and reduce tilt angle. The morphological evolution of the etched sidewalls with wet etch time for the device structures is also thoroughly investigated. Consistent etch results are achieved for AlxGa1-xN alloys with Al compositions up to 70%, indicating the effectiveness of our etching process.