Maria Atanasova

Maria Atanasova

Auto-generated profile, based on publicly available information

Maria Atanasova

Department of Chemical Engineering, University of Pretoria, Hatfield, Pretoria, South Africa

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2021 in Thermochimica Acta
Verified
Journal Article
Closed access
JPJustin Phillips
Justin Phillips
MWMichelle Weldhagen
Michelle Weldhagen
TMThobile Mhlabeni
Thobile Mhlabeni
LRLucky Radebe
Lucky Radebe
SRShatish Ramjee
Shatish Ramjee
WFWalter W. Focke
Walter W. Focke

9 May 2023 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Open access
PDF file
DMDennis Simbarashe Moyo
Dennis Simbarashe Moyo
EMElizabet Van Der Merwe
Elizabet Van Der Merwe
MRMelanie Rademeyer
Melanie Rademeyer
FMFrederick Pieter Malan
Frederick Pieter Malan
MAMaria T. Atanasova
Maria T. Atanasova
WFWalter Wilhelm Focke
Walter Wilhelm Focke
This manuscript reports the investigation of the polymorphic behaviour of fipronil using a systematic comparison of the thermochemical and structural properties of different crystal forms obtained in this study as well as those previously reported in literature. The analytical techniques employed include DSC, TGA, PXRD, SCXRD and hot stage microscopy. DSC proved particularly useful because it made it possible to differentiate between the two different crystal forms found in the as-received neat fipronil. The DSC scans revealed the presence of two polymorphs which had melting endotherms with peak maxima at ca. 196 °C and 205 °C, respectively. These polymorphs were successfully separated via sublimation and resulted in a metastable, lower melting polymorph in the sublimate and a thermodynamically stable, higher melting form in the sublimation residue. Clear evidence for the instability of the lower melting polymorph was found when the endotherms were examined under a range of heating rates. The proportion of the metastable form appeared to increase as the rate was increased, indicating that the metastable form underwent a solid–solid phase transition to the stable form at low heating rates. Recrystallization of fipronil from different solvents yielded five different forms. TGA curves revealed that all forms, except the acetone-derived one, were solvate pseudo-polymorphs that showed solvent loss between 60 and 100 °C. The acetone-derived sample was a hemihydrate that only started to show mass loss at 120 °C. SCXRD studies revealed that three of the five forms have similar structural characteristics, while the other two forms differ notably from each other and the rest of the structures. Despite these structural differences, all five forms exhibit near-identical intra- and intermolecular hydrogen bond networks.

24 June 2025 in Journal of Fire Sciences
Verified
Journal Article
Open access
WFWalter Wilhelm Focke
Walter Wilhelm Focke
WMWashington Mhike
Washington Mhike
Joseph AsanteJoseph Asante
Joseph Asante
IWIsbé van der Westhuizen
Isbé van der Westhuizen
ESEduard Jacobus Snyman
Eduard Jacobus Snyman
MAMaria Atanasova
Maria Atanasova
Treatment of Palabora vermiculite with ammonium chloride or ammonium nitrate solutions caused the collapse of its structure, resulting in a reduction of the exfoliation onset temperature by more than 200°C. It is speculated that ammonium ions enter the hydrobiotite galleries as guest ions partially replacing the hydration water associated with the magnesium ions. The effectiveness of various modified vermiculite flakes as flame-retardant fillers was evaluated in laminates of high-density polyethylene and plasticized polyvinyl chloride/vermiculite-modified composites. The laminates comprised a high-density polyethylene sheet coated with polyvinyl chloride plasticized with 100 phr of a phosphate ester and filled with 40 phr vermiculite. Cone calorimetry results, measured at a radiant flux of 35 kW m −2 , revealed that copper-ion modified vermiculite was the most effective flame-retardant additive. Laminates coated with polyvinyl chloride containing copper-ion-modified vermiculite exhibited a significantly reduced peak heat release rate of 64kW/m 2 , compared to 677kW/m 2 for uncoated high-density polyethylene, demonstrating the potential of polyvinyl chloride–based flame-retardant coatings incorporating copper-ion-modified vermiculite for polyethylene.