Reduced power processing is a new trend to improve the conversion efficiency of LED driver systems. Based on the concept, a new LED driver architecture is proposed in this paper, which requires fewer power semiconductors compared with prior works, leading to the potential of lower cost and higher efficiency. A new AC/DC LED driver topology is derived accordingly based on the architecture to achieve constant output current and unity power factor with significant energy storage reduction of the 100/120Hz energy buffer. Through a split and shared inductor, the required magnetic energy storage in the derived topology is the same as the conventional single-stage PFC converter, indicating high power density. Experimental evaluation verifies the performance in terms of improved power quality and conversion efficiency.
8 March 2022 in IEEE Transactions on Power Electronics
Recent developments of fast-charging power delivery protocols are driving ACDC adapters to hundred-watt power ranges. Conventional solutions in this power range employing a two-stage topology and a big twice-line frequency buffer capacitor are generally costly and bulky. This paper presents a patent-pending modulation method for an active clamp flyback converter, allowing for a single-stage adapter design with reduced capacitance requirements and a higher efficiency. This is achieved by exploiting the inherent energy storage capability of the clamping capacitor while turning it into an active power buffer. No hardware modifications are needed, while all salient features of active-clamp flyback converter, i.e., soft switching and leakage recycling, are retained. Operating principles and detailed controller design are discussed, and a 100-W laboratory prototype is built. The prototype achieves 94 % peak efficiency and up to 92 % size reduction of the buffer capacitor. The experimental evaluation shows the new single-stage solution enabled by the proposed modulation method is superior to the conventional two-stage and single-stage solutions in terms of cost, conversion efficiency, and power density.
13 February 2023 in IEEE Transactions on Power Electronics
To mitigate the bulky and heavy twice-line frequency power buffer in single-phase power-factor-correction (PFC) rectifiers while maintaining a lower cost, active-power-decoupling integrated active clamp flyback (iACF) PFC rectifier is recently proposed in the literature. The solution inherits all the benefits of conventional ACF converters such as low component count, leakage energy recycling, and soft-switching while being able to reduce the size of the power buffer in the system without hardware modifications. However, existing modulation and control strategies, based on continuous-conduction-mode (CCM), can only achieve a high efficiency at heavy load but not at light load. This article proposes a new modulation to improve the light-load efficiency of iACF PFC rectifiers. By combining CCM and burst mode of operation, this new modulation method can maintain all good features of CCM while effectively reducing the operating frequency, thus reducing the switching losses of the system at light load. This article, first, reviews the existing light-load modulation methods for ACF converters and limitations of applying these methods to iACF are highlighted. The detailed operating principles of the proposed modulation method are explained, and controller implementation that supports simultaneous full-load, medium load and ultralight load operation is developed. A 100-W laboratory iACF prototype is developed to verify the feasibility of the proposal, showcasing a 4-point average efficiency 91.9%, superior to the conventional two-stage solutions.
Light‐emitting‐diode (LED) drivers are required to maintain the power quality of both the AC input and DC output side. The regulation prevents adverse impacts on the grid and maintains the nominal operating condition of LEDs. Without significant filtering, the input power from a single‐phase AC source can result in low‐frequency flickers that raise health issues. This study proposes a LED driver topology to achieve low harmonics at the AC side and maintain flicker‐free operation to drive LEDs. A novel ripple‐cancelling scheme is developed to minimise redundant power processing and reduce circuit complexity to achieve high‐conversion efficiency. The new topology supports a simple control strategy to operate the driver effectively. Experimental evaluation demonstrates the system performance and verifies the novelty and contribution.
1 December 2022 in IEEE Transactions on Power Electronics
Conventional two-stage power factor correction (PFC) architecture based on a boost PFC front end and an isolated dc–dc back end is increasingly challenged by the recent trend toward higher power density and efficiency. One key reason for the challenge is the difficulty of increasing the operating frequency of the boost PFC stage. This article presents a new star PFC architecture that allows the boost PFC stage to operate efficiently at a higher frequency while maintaining the performance of the second dc–dc stage, leading to a high-power-density and high-efficiency ac–dc converter design across a universal input. The high performance of star architecture is enabled by realizing: 1) continuous-conduction-mode (CCM) operation of the boost PFC stage; and 2) full-range zero-voltage-switching (ZVS) of all active switches. In addition, the star architecture can: 1) operate at a constant frequency via a proper selection of the circuit topology and modulation method; and 2) be controlled based on simple and low-cost analog circuits. A 300-kHz, 240-W, 48-V-output, and universal-input prototype is built to verify the performance of the star architecture, showcasing high power factor, constant output voltage, 97.1 % full-load efficiency, 55.6 W/in $^{3}$ power density by box volume.
8 November 2022 in IEEE Transactions on Power Electronics
Critical conduction mode (CRM) boost power factor correction (PFC) front end is one of the most popular solutions to universal ac–dc applications below 300 W for its simplicity and high efficiency. However, its power density is largely limited by the need for a relatively bulky inductor and a buffer capacitor. This article introduces a new PFC front end that enables simultaneous size reduction of both the inductor and the buffer capacitor by achieving zero-voltage-switching of all switches and active power buffering. A 100-W universal input prototype is built, measuring a 96.7% peak efficiency and 50.8-W/in $^{3}$ power density. Compared to a typical CRM boost PFC front end, the prototype achieves a 47% size reduction of the magnetics, a 21% size reduction of the buffer capacitor, and an almost constant dc-link voltage, while maintaining comparable efficiency performance.