We report on a path-independent insertion-loss (PILOSS) 8 × 8 matrix switch based on Si-wire waveguides, which has a record-small footprint of 3.5 × 2.4 mm2. The PILOSS switch consists of 64 thermooptic Mach-Zehnder (MZ) switches and 49 low-crosstalk intersections. Each of the MZ switches and intersections employs directional couplers, which enable the composition of a low loss PILOSS switch. We demonstrate successful switching of digital-coherent 43-Gbps QPSK signal.
13 November 2006 in IEEE Transactions on Nanotechnology
The titanium nitride (TiN) gate electrode with a tunable work function has successfully been deposited on the sidewalls of upstanding Si-fin channels of FinFETs by using a conventional reactive sputtering. It was found that the work function of the TiN (phiTiN) slightly decreases with increasing nitrogen (N2) gas flow ratio, RN=N2/(Ar+N2) in the sputtering, from 17% to 100%. The experimental threshold voltage (Vth) dependence on the RN shows that the more RN offers the lower Vth for the TiN gate n-channel FinFETs. The composition analysis of the TiN films with different RN showed that the more amount of nitrogen is introduced into the TiN films with increasing RN, which suggests that the lowering of phi TiN with increasing RN should be related to the increase in nitrogen concentration in the TiN film. The desirable Vth shift from -0.22 to 0.22 V was experimentally confirmed by fabricating n+ poly-Si and TiN gate n-channel multi-FinFETs without a channel doping. The developed simple technique for the conformal TiN deposition on the sidewalls of Si-fin channels is very attractive to the TiN gate FinFET fabrication
1 March 2014 in IEEE Transactions on Nanotechnology
Ultrashort-channel junctionless FETs (JL-FETs) were fabricated on silicon-on-insulator substrates utilizing atomically sharp V-shaped grooves produced by anisotropic wet etching. The channel length, defined as the width of the V-groove bottom, was as short as 3 nm, and the channel thickness was between 1 and 8 nm. Excellent transistor characteristics with threshold voltages that are optimal for low-power operation were obtained for both n-FETs and p-FETs when the thickness of both the channel and gate dielectric film thickness was reduced to 1 nm. The origin of the excellent electrostatic control is discussed on the basis of fringe capacitance and quantum confinement effects in a nanometer-scale ultrathin Si layer where band-gap expansion, dielectric constant reduction, and increase in the dopant activation energy become prominent. The electrical characteristics of the ultrashort channel JL-FETs were found to be very sensitive to device parameters such as the channel thickness and dopant concentration.
Variability of TiN FinFET performance is comprehensively studied. It is found that the variation of the in the FinFET occurs and the standard deviations of the of nMOS and pMOS FinFETs are almost the same. From the analytical results, it is found that the variation of the TiN FinFET is due to the work function variation (WFV) of TiN metal gate. The WFV is also responsible for the on-current variation.
In this letter, we propose a synthetic electric field (SE) effect to enhance the performance of tunnel field-effect transistors (TFETs). The novel SE-TFET architecture utilizes both horizontal and vertical electric fields induced by a gate electrode that is wrapped around an ultrathin epitaxial channel. The drain current of the SE-TFET is increased up to 100 times in comparison with those of conventional TFETs. The subthreshold slope of the SE-TFET also improved, and enhanced to 52 mV/decade by scaling the channel width and channel thickness.
26 May 2016 in IEEE Transactions on Circuits and Systems II: Express Briefs
A fully integrated step-up dc-dc converter for energy harvesting applications is presented. A minimum start-up voltage of 100 mV is achieved by the start-up mechanism based on an LC oscillator (LCO). Conventional voltage converters with the LCO-based start-up mechanism provide a significantly low conversion efficiency of around 1%. To overcome this drawback, the following two circuit techniques are proposed in this brief: 1) a gate-boosted charge pump; and 2) an LCO deactivation. The proposed voltage converter is fabricated in the 65-nm silicon-on-thin-buried-oxide process. The measurement results show that when the input voltage is 100 mV, the proposed converter can provide an output of 760 mV at a conversion efficiency of 33%, which is the highest efficiency compared with the conventional fully integrated voltage converters.