Ewa Wojtiuk

Ewa Wojtiuk

Auto-generated profile, based on publicly available information

Ewa Wojtiuk

Warsaw University of Technology

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 November 2025 in Journal of Alloys and Compounds
Verified
Journal Article
Open access
EWEwa Wojtiuk
Ewa Wojtiuk
MMMarcin Maździarz
Marcin Maździarz
TSTomasz Stasiak
Tomasz Stasiak
MBMarcin Brykała
Marcin Brykała
MCMarcin Chmielewski
Marcin Chmielewski
TMTomasz Mościcki
Tomasz Mościcki

30 March 2024 in Welding Technology Review
Verified
Journal Article
Open access
PDF file
EWEwa Wojtiuk
Ewa Wojtiuk
JRJoanna Radziejewska
Joanna Radziejewska
MMMichał Marczak
Michał Marczak
The article presents research on finishing treatment applied to components made of Inconel through 3D printing by Laser Powder Bed Fusion method. Vibration-abrasive machining was carried out using a supporting fluid and various shapes of abrasive. The effects of the processing conditions were analysed based on the surface roughness of the samples and mass loss. The obtained collective results were subjected to comparative analysis with the effects of vibratory-abrasive processing without the use of a processing fluid, as presented in the article. The research has shown that using vibration-abrasive processing, it is possible to reduce the height of surface irregularities by more than three times after four hours of treatment. The intensity of processing was the highest in the first hour of the process. The lowest roughness heights Ra = 1.8 μm were obtained using ceramic balls in the presence of a supporting fluid.

15 May 2026 in Ceramics International
Verified
Journal Article
Closed access
KZKatarzyna Zielińska
Katarzyna Zielińska
MWMateusz Włoczewski
Mateusz Włoczewski
RPRafał Psiuk
Rafał Psiuk
Jacek HoffmanJacek Hoffman
Jacek Hoffman
EWEwa Wojtiuk
Ewa Wojtiuk
Moscicki TomaszMoscicki Tomasz
Moscicki Tomasz

1 June 2026 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Open access
Moscicki TomaszMoscicki Tomasz
Moscicki Tomasz
PWPaweł Widomski
Paweł Widomski
MKMarcin Wrocławska Kaszuba
Marcin Wrocławska Kaszuba
EWE. Wojtiuk
E. Wojtiuk
TSTomasz Stasiak
Tomasz Stasiak
Smolik JerzySmolik Jerzy
Smolik Jerzy
The limited lifetime of hot forging tools, caused by severe wear mechanisms such as abrasion, adhesion, thermal fatigue, and plastic deformation, remains a major challenge in forging operations. The study encompasses the entire process, from concept to industrial implementation. It begins with basic laboratory tests of the innovative material, followed by the application of protective coatings on an industrial scale to forging dies, which were then successfully used in production. The research presents the development and evaluation of novel hybrid surface treatments combining plasma nitriding with nanocomposite coatings based on tungsten boride alloyed with either tantalum (W-Ta-B) or titanium (W-Ti-B). The coatings were deposited using High Power Impulse Magnetron Sputtering (HiPIMS) from SPS-fabricated ternary targets. Laboratory characterization included structural, mechanical, tribological, and oxidation resistance analyses. The W-Ti-B films exhibited superhardness above 40 GPa and superior wear resistance, while the W-Ta-B coatings demonstrated enhanced oxidation resistance and adhesion. Both coatings revealed fine columnar microstructures and favorable H/E* and H³/E² ratios, indicating high resistance to plastic deformation and cracking. Industrial trials under hot forging conditions confirmed their effectiveness, with tool life extended by up to 80% compared with conventional nitrided tools. These findings demonstrate the strong potential of HiPIMS-deposited W-based boride coatings to significantly improve tool performance in demanding thermal and mechanical environments.