Karina Aparecida Martins Barcelos Gonçalves

Karina Aparecida Martins Barcelos Gonçalves

Auto-generated profile, based on publicly available information

Karina Aparecida Martins Barcelos Gonçalves

Department of Metallurgy and Chemistry, Centro Federal de Educação Tecnológica de Minas Gerais, R. 19 de Novembro, 121, Centro Norte, Timóteo 35180-008, MG, Brazil

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 July 2018 in Materials Research
Verified
Journal Article
Open access
PDF file
KGKarina Aparecida Martins Barcelos Gonçalves
Karina Aparecida Martins Barcelos Gonçalves
DSDagoberto Brandão Santos
Dagoberto Brandão Santos
TOTarcísio Reis de Oliveira
Tarcísio Reis de Oliveira
Samples of duplex stainless steel 32205 (standard duplex) and 32304 (lean duplex) were investigated in the as-received state, cold rolling (with thickness reduction of 64 % and 62 % respectively) and after annealing at 1055ºC for 20 s soaking. Crystallographic microtexture was obtained via Electron BackScatter Diffraction (EBSD) technique. The results showed that the crystallographic microtexture of ferrite phase in the as-received, cold rolled and annealed condition were more intense in alpha fiber= // RD and tetha fiber. The austenite microtexture was shown to be, for all conditions, mainly composed by Brass component.

1 January 2024 in Advances in Mechanical and Materials Engineering
Verified
Journal Article
Closed access
PDF file
TBThales Harvey Crisóstomo Barros
Thales Harvey Crisóstomo Barros
IGIgor Augusto Dias Gonzaga
Igor Augusto Dias Gonzaga
ANAlmir Silva Neto
Almir Silva Neto
EAErriston Campos Amaral
Erriston Campos Amaral
KGKarina Aparecida Martins Barcelos Gonçalves
Karina Aparecida Martins Barcelos Gonçalves
VLVALMIR DIAS LUIZ
VALMIR DIAS LUIZ
In this paper, the effect of sheet pre-deformation on the change of the surface roughness parameters and friction coefficient value is investigated. For this purpose, strips of AISI 430 ferritic stainless steel with deep drawing quality (DDQ), measuring 0.8 × 25 × 500 mm, were pre-deformed using a uniaxial tensile test for five different true strain values. The correlation between the surface roughness parameters and hardness with the frictional conditions of the tested strips was investigated in the bending under tension test. The results revealed that the friction coefficient determined for all pre-deformed strips increased as the level of true strain also increased. An increase in the plastic deformation of sheets under the uniaxial tensile stress state causes a nearly linear increase in the value of basic amplitude parameters of surface roughness, however, the hardness tended to present a constant increase for deformations close to uniform elongation. Furthermore, scratches and severe wear occurred on the surface of the strips and intensified with increasing roughness.

1 January 2024 in Advances in Mechanical and Materials Engineering
Verified
Journal Article
Closed access
EOEduarda Soares Oliveira
Eduarda Soares Oliveira
JDJuliana Rodrigues Damasceno
Juliana Rodrigues Damasceno
ANAlmir Silva Neto
Almir Silva Neto
EAErriston Campos Amaral
Erriston Campos Amaral
KGKarina Aparecida Martins Barcelos Gonçalves
Karina Aparecida Martins Barcelos Gonçalves
VLVALMIR DIAS LUIZ
VALMIR DIAS LUIZ
Friction is an unfavourable phenomenon in sheet metal forming processes because it increases the forming force, reduces the surface quality of the drawpieces and affects the increased wear of the forming tools. This article presents the results of experimental studies on friction occurring due to the drawing die radius. The test materials used were 0.8-mm-thick strip samples made of AISI 430 steel and AW-1100 aluminium alloy sheets. A special bending under tension friction-test simulator was used to carry out the tests. Countersamples (pins) with different radii in the range of 1.5 mm to 13.5 mm were used. The tests were carried out at room temperature under mineral-based oil lubrication conditions. The friction tests were supplemented by determining the hardness and measuring the surface roughness (parameters Ra, Rq and Rt) of the samples. Based on the results, it was found that the coefficient of friction increased with a decrease in the bending pin radius, however, this behaviour changed above a critical radius (4.5 mm), after which the coefficient of friction increased with an increase in the pin radius. Furthermore, the AW-1100 aluminium alloy strip had a higher coefficient of friction than the AISI 430 steel strip.