Erriston Campos Amaral

Erriston Campos Amaral

Auto-generated profile, based on publicly available information

Erriston Campos Amaral

Department of Metallurgy and Chemistry, Centro Federal de Educação Tecnológica de Minas Gerais, R. 19 de Novembro, 121, Centro Norte, Timóteo 35180-008, MG, Brazil

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2024 in Advances in Mechanical and Materials Engineering
Verified
Journal Article
Closed access
PDF file
TBThales Harvey Crisóstomo Barros
Thales Harvey Crisóstomo Barros
IGIgor Augusto Dias Gonzaga
Igor Augusto Dias Gonzaga
ANAlmir Silva Neto
Almir Silva Neto
EAErriston Campos Amaral
Erriston Campos Amaral
KGKarina Aparecida Martins Barcelos Gonçalves
Karina Aparecida Martins Barcelos Gonçalves
VLVALMIR DIAS LUIZ
VALMIR DIAS LUIZ
In this paper, the effect of sheet pre-deformation on the change of the surface roughness parameters and friction coefficient value is investigated. For this purpose, strips of AISI 430 ferritic stainless steel with deep drawing quality (DDQ), measuring 0.8 × 25 × 500 mm, were pre-deformed using a uniaxial tensile test for five different true strain values. The correlation between the surface roughness parameters and hardness with the frictional conditions of the tested strips was investigated in the bending under tension test. The results revealed that the friction coefficient determined for all pre-deformed strips increased as the level of true strain also increased. An increase in the plastic deformation of sheets under the uniaxial tensile stress state causes a nearly linear increase in the value of basic amplitude parameters of surface roughness, however, the hardness tended to present a constant increase for deformations close to uniform elongation. Furthermore, scratches and severe wear occurred on the surface of the strips and intensified with increasing roughness.

1 January 2022 in Matéria (Rio de Janeiro)
Verified
Journal Article
Open access
VLVALMIR DIAS LUIZ
VALMIR DIAS LUIZ
EAErriston Campos Amaral
Erriston Campos Amaral
VSVitor Pagani de Souza
Vitor Pagani de Souza
PRPaulo César de Matos Rodrigues
Paulo César de Matos Rodrigues
RESUMO Na conformação de chapas metálicas, as propriedades mecânicas do material e os aspectos relacionados ao atrito têm sido uma das principais preocupações, pois têm grande influência na produtividade, qualidade do produto e custos de produção. Nesse contexto, é de extrema importância compreender e ser capaz de controlar os diferentes fatores que afetam o atrito durante o processo de deformação plástica. O objetivo deste trabalho foi investigar a influência da variação da velocidade de estampagem e da anisotropia no comportamento tribológico e na fratura de uma tira de aço inoxidável ferrítico AISI 430 estabilizado com Nb deslizando sobre um pino de metal duro (WC-12% Co). Para isso, foi utilizado um teste de conformabilidade que simula o atrito entre a chapa e a ferramenta. O coeficiente de atrito, ductilidade e dureza na fratura foram medidos para investigar o efeito da velocidade de ensaio e da anisotropia da chapa de aço nos resultados experimentais. Uma análise comparativa dos resultados revelou que o coeficiente de atrito diminuiu com o aumento da velocidade de teste. Além disso, a orientação da tira metálica influenciou sintomaticamente no atrito, sendo maior no sentido de laminação, cuja rugosidade superficial foi maior que no sentido transversal. Como resultado da deformação plástica, a dureza e resistência da chapa de aço aumentaram, mas a ductilidade diminuiu, porém, o aumento da velocidade de ensaio também influenciou os valores desses parâmetros causando uma diminuição, muito provavelmente, devido ao aumento da temperatura na interface de contato.

1 January 2024 in Advances in Mechanical and Materials Engineering
Verified
Journal Article
Closed access
EOEduarda Soares Oliveira
Eduarda Soares Oliveira
JDJuliana Rodrigues Damasceno
Juliana Rodrigues Damasceno
ANAlmir Silva Neto
Almir Silva Neto
EAErriston Campos Amaral
Erriston Campos Amaral
KGKarina Aparecida Martins Barcelos Gonçalves
Karina Aparecida Martins Barcelos Gonçalves
VLVALMIR DIAS LUIZ
VALMIR DIAS LUIZ
Friction is an unfavourable phenomenon in sheet metal forming processes because it increases the forming force, reduces the surface quality of the drawpieces and affects the increased wear of the forming tools. This article presents the results of experimental studies on friction occurring due to the drawing die radius. The test materials used were 0.8-mm-thick strip samples made of AISI 430 steel and AW-1100 aluminium alloy sheets. A special bending under tension friction-test simulator was used to carry out the tests. Countersamples (pins) with different radii in the range of 1.5 mm to 13.5 mm were used. The tests were carried out at room temperature under mineral-based oil lubrication conditions. The friction tests were supplemented by determining the hardness and measuring the surface roughness (parameters Ra, Rq and Rt) of the samples. Based on the results, it was found that the coefficient of friction increased with a decrease in the bending pin radius, however, this behaviour changed above a critical radius (4.5 mm), after which the coefficient of friction increased with an increase in the pin radius. Furthermore, the AW-1100 aluminium alloy strip had a higher coefficient of friction than the AISI 430 steel strip.