The accuracy of motor characteristics prediction according to driving cycle can be improved by taking temperature change of motor into account. From this point of view, this paper proposes a fast and accurate coupled analysis method. To calculate motor circuit parameters, electromagnetic finite element analysis (FEA) is used. The proposed method consists of two stages to exclude the time consuming FEA from repetitive process. In pre-process stage, the circuit parameters are stored as look-up tables (LUTs) considering motor temperature. Further, a technique that allows reducing the number of analyses is developed to consider a wide operating temperature range with less time consumption. In main process stage, the torque and voltage equations are solved using the circuit parameter LUTs. Among the solved motor characteristics, losses are applied to lumped parameter thermal network (LPTN) as heat sources to figure out thermal characteristics. Here, techniques including loss separation and thermal parameter tuning are introduced to improve both accuracy and speed of the LPTN. Since the computation of the characteristic equations and LPTN are fast, the iterative analysis at entire time steps of the driving cycle is facilitated. An example of the proposed method is presented using worldwide harmonized light vehicle test procedure (WLTP). Thereafter, the effectiveness of the method is discussed by comparison with conventional methods. Finally, the experimental verifications are conducted to validate the electromagnetic FEA and LPTN used in this study.
3 May 2019 in IEEE Transactions on Vehicular Technology
Hybrid electric vehicles have different performance depending on power distribution and energy management. For heavy-duty vehicles, in particular, these differences will be more pronounced. This paper presents a hybrid powertrain design framework for a heavy-duty multi-purpose vehicle assuming driving conditions. A diesel-powered conventional vehicle was adopted for the hybridization target, and a series hybrid system was suggested as a suitable hybridization topology with an in-wheel motor (IWM) system. The introduced framework supplied the adequate power distribution and the IWM specification based on the speculated drive cycle and a simple energy management strategy. In particular, the reduction ratio of IWM was determined to minimize the gross mass of the motor and reduction gear. The hybridization reduced the vehicle weight by 213 kg while increasing the peak power by 53 kW. Finally, the vehicle simulation was performed using the advanced vehicle simulator for the design result from the proposed framework. The acceleration performance and gradeability limits were improved by 18 % and 10 %p, respectively, compared to the conventional vehicle. In addition, the gasoline equivalent fuel economy of the series hybrid powertrain was 53 % higher than conventional diesel powertrain for the target drive cycle.
1 January 2020 in The World Journal of Men's Health
The performance of motors can vary considerably, depending not only on the design but also the manufacturing process. In particular, for motors used in systems wherein vibration and noise are important, the characteristics of the motors change according to the manufacturing method; hence, it is essential to study the effect of the manufacturing process on the characteristics of motors. In this study, motors with a connected core and segmented core are compared and analyzed; particularly, the motors are intended for use in a brake system. The general strengths and weaknesses of each core type are determined, and the electrical and mechanical properties of the motors are analyzed through finite element analysis (FEA). The motors are applied to an integrated brake system that does not employ a vacuum booster, and motors with each type of core are fabricated and tested to verify their characteristics. Finally, the analysis results obtained using FEA and the test results are compared and analyzed to evaluate the validity of this study.
20 September 2021 in Journal of Electrical Engineering & Technology
This paper proposes a method for predicting the load noise of high-voltage (HV) transformers. When the transformer is loaded, the electromagnetic force is generated by the interaction between electric and magnetic fields. This force, the so-called Lorentz force, induces the vibration of the winding structure causing the load noise of transformer. Therefore, calculating the Lorentz force plays a crucial role in predicting the load noise. Herein, a 3-Dimensional equivalent magnetic circuit network (3-D EMCN) is applied to calculate the Lorentz force, instead of 3-Dimensional finite element analysis (3-D FEA) to shorten the computation time. Subsequently, considering the relationship between the sound pressure and the Lorentz force, the calculated force can be applied in the equation for the sound pressure level (SPL), which represents the relative sound pressure on a logarithmic scale. The formula for the sound pressure varies depending on the sound source model. The source model of load noise can be represented as a dipole source because the structure of the transformer windings is considered as an unbaffled speaker. The transformer parameters identified to affect the load noise are additionally considered for more accurate prediction of load noise. The parameters identified to increase the load noise are simply multiplied to the equation, whereas those with the opposite effect are multiplied inversely. Finally, after this compensation process, the accuracy of the load noise prediction equation is calculated as the standard deviation of the differences between the experimental and calculated results.