James Egbu

James Egbu

Auto-generated profile, based on publicly available information

James Egbu

Materials Science and Engineering, Carnegie Mellon University, Pittsburgh, PA, USA

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 May 2019
Verified
Conference Paper
Open access
PDF file
RWRuishu F. Wright
Ruishu F. Wright
MBMudabbir Badar
Mudabbir Badar
JEJames C. Egbu
James C. Egbu
PLPing Lu
Ping Lu
Michael BuricMichael Buric
Michael Buric
POPaul Ohodnicki
Paul Ohodnicki
Internal corrosion can occur when aqueous electrolytes are present inside natural gas transmission pipelines. Despite upstream gas dehydration treatments, liquid water can form through condensation of water vapor or may be introduced from plant upsets. With dissolved salts and acidic gases such as CO2 and H2S, aqueous electrolytes become very corrosive with increased conductivity and lower pH. Since water provides the electrolytes that initiate and sustain corrosion, detection of water can locate the spots for potential internal corrosion inside the pipelines. In this work, a simple optical fiber-based sensor for fully distributed water monitoring has been demonstrated and studied. The system consists of an unmodified off-the-shelf single mode (SM) optical fiber and an optical backscatter reflectometer (OBR) capable of measuring the spatial profile of strain changes along the fiber. The polymer jacket coating of the SM fiber is hydroscopic and serves as the water sensing layer due to expansion/swelling from water absorption. The swelling induced strain change is interrogated with the OBR to enable fully distributed water monitoring. This strain-based H2O sensor is sensitive to H2O molecules regardless of the phase (liquid or vapor) or the surrounding media. Strain changes were measured at different relative humidity levels from 0% to 100% to demonstrate reversibility and linear correlation between humidity and strain. This sensor has the advantages of fully distributed sensing, low cost, simple preparation, easy operation, and good sensitivity.

30 March 2022 in Materials Research Bulletin
Verified
Journal Article
Closed access
ATAhmed Talaat
Ahmed Talaat
JEJ. Egbu
J. Egbu
CPC. Phatak
C. Phatak
KBK. Byerly
K. Byerly
MMM.E. McHenry
M.E. McHenry
POPaul Ohodnicki
Paul Ohodnicki

9 June 2023 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
JEJ. Egbu
J. Egbu
ALA. Leary
A. Leary
KBK. Byerly
K. Byerly
SSS. Simizu
S. Simizu
ETE. Thiesen
E. Thiesen
MMM. McHenry
M. McHenry
Recently developed FeNi-based metal amorphous nanocomposites (MANCs) used in high-speed motors (HSMs) exhibit reduced eddy current losses while maintaining good mechanical properties and glass-forming abilities. Magnetic anisotropy in (Fe 70 Ni 30 ) 80 Nb 4 B 14 Si 2 amorphous magnetic ribbon (AMR) in the as-cast state and upon conventional (T CA ) and strain (T SA ) annealing heat treatment is investigated. From ribbon samples in as-cast condition, quenched in stress from planar flow casting (PFC) induced as-cast curvature derived uniaxial magnetic anisotropy. Stress relief by conventional furnace annealing at T CA > 350 °C achieved isotropic properties in the bulk. Annealing about the primary crystallization temperature, T CA ~ 450 °C, resulted in the formation of both FCC and BCC nanocrystallites and evolution to isotropic bulk magnetic properties confirming the random anisotropy model. In samples strain annealed at T SA = 440 °C at various tensions, relatively large controlled induced uniaxial anisotropy is achieved. The largest magnetic anisotropy occurs in annealing under the stress of 250 MPa yielding an anisotropy field of 7.1 x 10 4 A/m. Surface anisotropy observed by MOKE differs from bulk anisotropy due to image contrast from closure domains. Epoxy coatings are important for improved bonding, mechanical properties, and resistivity in tape-wound MANC cores for HSMs. Using a sessile droplet method, the equilibrium contact angle of an epoxy droplet on a tensile stress annealed MANC exhibits stress dependent surface energies. Anisotropic wetting in FeNi-based MANC heat treated at T CA = 440 °C mimics surface magnetic anisotropy observed by MOKE.

20 October 2021
Verified
Conference Paper
Closed access
PDF file
JEJames Egbu
James Egbu
POPaul Ohodnicki
Paul Ohodnicki
RWRuishu Wright
Ruishu Wright
JBJohn Baltrus
John Baltrus
MMMichael McHenry
Michael McHenry
New interest in high performance soft magnetic materials (SMMs) have been fueled by the need to lower losses at higher operating frequencies while maintaining high flux density and tunable permeability in electrical motors, transformer, and generator applications. Conventional SMMs like electrical steels and Fe-based metal amorphous nanocomposite (MANC) alloys are dominated by eddy current losses at high frequencies. Recent breakthrough in high-performance FeNi MANC have shown promise in reducing eddy current losses as compared to electrical steels. Their intrinsic adherent native surface oxide layer provides sufficient electrical insulation to reduce interlaminate eddy current losses. However, notwithstanding advances in MANCs, there exists a gap in literature on investigations of the surface oxide layer responsible for significant reduction of interlaminate eddy current losses in magnetic cores. This work presents a detailed characterization of the surface oxide, oxidation behavior, and relationship between oxide thickness and resistivity of a new FeNi MANC alloy (Fe70Ni30)80Nb4B14Si2.

13 July 2018 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
JEJames Egbu
James Egbu
BMBenjamin Martin
Benjamin Martin
Global battery manufacturing capacity will more than double by 2021 to about 280,000 megawatt-hours.1 Rechargeable batteries make up a significant fraction of battery manufacturing. A rechargeable battery cell is made up of two electrodes, the anode and the cathode, separated by an electrolyte. For solid electrodes, an electrolyte-permeable separator separates them. Chemical reactions at the anode and the cathode produces two components; ionic and electronic. The electrolyte conducts the movement of ions inside the cell while forcing electrons to pass through outside of the cell. Current collectors at the anode and the cathode deliver electric current to and from the external circuit. During discharge, electrons and ions flow from the anode to the cathode. On charge, an applied electric field forces the electrons and ion to flow back from the cathode to the anode.2 Lithium-ion technology has dominated the rechargeable battery industry because of their high energy density, and portability. High cost, safety issues, and charge storage capacity limit lithium-ion technology. These problems have sparked new interest in rechargeable batteries with multivalent ions like magnesium ion (Mg-ion). Magnesium is divalent, cheaper than lithium, easy to handle, and environmentally friendly. It has 1.85 times the theoretical volumetric capacity of lithium.3 Passivation and choice of cathode materials have hindered Mg-ion technology. Passivation produces a surface thin film on the metal anode that prevents reversibility of magnesium ions. Electrolytes from magnesium organo-halo-aluminate complexes in ether solvents have significantly reduced passivation problems.4 The choice of cathode material remains elusive. Theoretical predictions have shown high magnesium ion mobility in six-coordination, spinel close-packed frameworks.5 Mg-ion has been reported to favor octahedral environment in oxides and sulfides.6 This project focuses on investigating vanadium sulfides compounds, AxV5S8, AxV6S8, and V5S8 as candidate cathode materials for Mg-ion battery. A is an alkali metal, or monovalent cation and x = 0 – 0.8. AxV6S8 has a hexagonal unit cell formed from a distorted VS6 octahedral sharing faces and edges, with large hexagonal channels capable of intercalating ions.7 AxV5S8 has a monoclinic structure. It has a three-dimensional framework made from slightly distorted VS6 octahedral sharing edges and faces, with rectangular tunnels prime for ion insertion.8 Both AxV5S8 and AxV6S8 have short V-V zigzag chains that make both metallically conductive.5,6 V5S8 has a monoclinic structure with every three-quarter of metal atom position vacant in every layer of the NiAs structure.9 Stoichiometry mixtures of vanadium sulfide compounds are synthesized in evacuated sealed quartz tubes. The products are handled and analyzed under argon. Samples of AxV6S8, AxV5S8, and V5S8 are characterized using powder XRD. Electrochemical properties of the vanadium sulfide compounds are studied using cyclic voltammetry and chronopotentiometry. Cell assembly consists of lithium metal anode, 80 % vanadium sulfide compound cathode, 1 M LiClO4 in 1:1 EC:DEC electrolyte, glass frit, Kynar, and graphite. XRD pattern for as prepared KxV5S8 matched with a known KxV5S8 pattern in the International Center for Diffraction Data database (ICDD). KxV6S8 XRD pattern showed KxV5S8 phase peaks when matched with the ICDD database, indicating phase impurity. Potassium is not a big enough metal to make the AxV6S8 framework. The XRD patterns of RbxV5S8, RbxV6S8, and V5S8 matched with ICDD database patterns for each compound without showing any phase impurities. Cyclic voltammetry and chronopotentiometry data with a lithium anode and the lithium-ion electrolyte indicate that KxV5S8 and RbxV5S8 are not electrochemically active. V5S8 is electrochemically active. It shows significant oxidation and reduction peaks during cyclic voltammetry with a lithium anode. In the future, RbxV6S8 will be investigated for electrochemical activity. Intercalation reactions of magnesium ion will be investigated in the electrochemically active compounds of vanadium sulfide compounds for battery applications. Figure 1