19 November 2018 in IEEE Transactions on Electromagnetic Compatibility
This paper presents an efficient method to estimate jitter in a chain of CMOS inverters in the presence of multiple noise sources, including the power supply noise, input data noise, and the ground bounce noise. For this purpose, necessary noise transfer functions are derived and the recently developed EMPSIJ method [J. N. Tripathi, R. Achar, and R. Malik, “Efficient modeling of power supply induced jitter in voltage-mode drivers (EMPSIJ),” IEEE Trans. Compon., Packag.Manuf. Technol., vol. 7, no. 10, pp. 1691–1701, Oct. 2017.] is advanced to handle cascaded CMOS inverter stages. Results from the proposed method are compared with the results from a conventional EDA simulator, which demonstrate a significant speed-up using the proposed method for a comparable accuracy.
5 June 2019 in IEEE Transactions on Electron Devices
A new and interesting field-effect transistor (FET) structure based on multilayer HfS₂ as a channel material, integrated with Al μ-interdigitated electrodes (μ-IDEs) and HfO₂ as a gate dielectric is reported for the first time. The electrical performance of Al/HfO₂/HfS₂/Al)μ -IDE-based FETs exhibited the threshold voltage of ~ -2.72 V, generous subthreshold swing (SS) of ~ 70 mV/dec, substantial ION/IOFF ratio of ~ 10⁴, transconductance of ~ 1.5 μS, a significantly high electron mobility of ~ 56.7 cm²/Vs at Vds = 1 V, and low gate leakage current of ~ 47 nA/cm² at Vgs = -1 V. Therefore, moderate threshold voltage, generous SS, robust current saturation, ultralow off-state leakage current, and low operating voltage of the fabricated Al/HfO₂/HfS₂/Alμ -IDE, FETs show its potential for next-generation (NG) low-power FET applications.
31 May 2021 in IEEE Transactions on Electron Devices
This article presents an analytical approach to determine jitter for a CMOS inverter in the presence of power supply noise (PSN). The deviation in the transition edge of the output signal from its ideal timing is modeled accurately for each transition. A power series method is used to solve differential equations for different regions of transistors during output transition. The PSN has been expressed in Taylor series expression, aids to derive closed-form equation for time interval error (TIE). The obtained results from the proposed methodology closely match with electronic design automation (EDA) simulator results and verified on 40 nm Taiwan Semiconductor Manufacturing Company (TSMC) and 28 nm United Microelectronics Corporation (UMC) foundries, demonstrating accurate modeling of jitter.
18 April 2017 in IET Circuits, Devices & Systems
A symbolic analysis is presented to study a gain‐boosted telescopic operational transconductance amplifier (OTA) with cross‐coupled capacitor (positive feedback) across an auxiliary op‐amp. The effects of positive feedback capacitor (PFC) on the pole–zero doublet introduced by the auxiliary op‐amp are explored using analytical techniques and simulations. A complete transfer function of the OTA with PFC across the auxiliary op‐amp is derived and verified through circuit simulations. The results obtained from circuit simulation and modelled transfer function show good agreement with each other. Furthermore, the analytical expressions for the feedback capacitor in terms of pole–zero locations, unity gain bandwidth (UGBW) and phase margin (PM) are presented. It is shown that UGBW, PM and settling behaviour of the OTA can be tuned by the PFC. A systematic design approach to improve the PM and settling behaviour is discussed. On the basis of the theory presented, 17% improvement in 0.01% settling time is demonstrated.
18 October 2022 in IEEE Transactions on Electron Devices
There are indelible challenges related to transistor action and realization of emerging two-dimensional van der Waals (vdW) multilayer (2D $_{\text{ml}}\text{)}$ field-effect transistors (FETs), to the post silicon technology era. For scalability, a cost-effective large area ultrafine thin films interface and band alignment of multilayer channel material with compatible gate dielectric are essential. Here, 2D $_{\text{ml}}$ hafnium disulfide (HfS $_{\text{2}}\text{)}$ and ZrO $_{\text{2}}$ are employed as channel material and gate dielectric, respectively, and anticipated that vdW interaction of said structures entails the high-quality interface with trivial dangling bonds and defects caused by lattice mismatch. The investigated Al/ZrO $_{\text{2}}$ /HfS $_{\text{2}}$ /Al $_{\mu\text{-IDE}}$ FETs exhibit the subthreshold swing (SS) $\sim$ 65 mV/dec, $\textit{I}_{\biosc{on}}$ / $I_{\biosc{off}}$ ratio of $\sim$ 104, transconductance of $\sim$ 3.99 $\mu$ S, effective mobility of $\sim$ 74 cm $^{\text{2}}$ /Vs at $\textit{V}_{\text{gs}}$ of 2 V, and leakage current density of $\sim$ 33.8 nA/cm $^{\text{2}}$ at $\textit{V}_{\text{gs}}$ of $-$ 1 V. Thus, the steep SS, sturdy current saturation, low-voltage operation ( $\sim$ 3 V), and leakage current establish the potential candidature of HfS $_{\text{2}}$ and ZrO $_{\text{2}}$ -based 2-D FETs for both conventional and ubiquitous electronics.
18 November 2011 in IEEE Transactions on Circuits and Systems II: Express Briefs
Distortion associated with a three-terminal MOS parametric amplifier has been analyzed using Volterra series. A prototype design of an nMOS-based parametric amplifier with supporting circuits was integrated on a standard 0.13-μm CMOS technology. The measurement results and the theoretical characterization show a mean percentage error of 16% and 1.25% for second harmonic (A2) and third harmonic (A3), respectively.