Torsion-torque-sensing-based load-side acceleration control is proposed for a two-inertia resonance system in this paper. This control uses a torsion torque sensor installed in a reduction gear, and consists of a torsion torque controller and load-side disturbance observer (DOb). In the load side of the gear, the proposed control structure is equivalent to a conventional DOb-based acceleration controller on the motor side. Therefore, because the proposed controller suppresses resonance vibration in an acceleration dimension, torsion-torque-sensing-based load-side acceleration control has the capability of controlling the load-side acceleration. The problem of the conventional acceleration controller and the effectiveness of the proposed acceleration controller are verified by theoretical analysis, numerical simulations, and experiments. Robust stability for parameter variation and stable regions of control bandwidth are also analyzed.
3 December 2018 in IEEE Transactions on Industrial Electronics
This paper proposes a new force estimation approach based on the dither periodic component elimination Kalman filter and the disturbance observer for realization of a fine sensorless force control system under the existence of static friction. A dither signal is inserted to the desired reference signal to eliminate the effect of static friction of a ball-screw system. The disturbance observer estimates the periodical torque caused by dither signal. The dither periodic component elimination Kalman filter uses the periodical torque for the estimation of the high-order torque responses to achieve the torque estimation with the elimination of periodic component. The problem of noise in the force sensation and the effect of static friction are reduced effectively by using the dither periodic component elimination Kalman filter. Therefore, the bandwidth of the force sensing is increased and the wide band disturbance observer is achieved. As a result, this paper has accomplished the fine sensorless force control realization. The force control experiments of a ballscrew system are carried out to verify the validity and effectiveness of the proposed method.
6 October 2017 in IEEE Transactions on Industrial Electronics
In order to reduce the cost and the size of a single-phase to three-phase power converter, an electrolytic capacitor-less single-phase to three-phase inverter is proposed. As the system does not have energy storage, such as an electrolytic capacitor, it results in source current harmonics due to the spatial harmonics of the motor. Adding an inductor for filtering the source current harmonics increases the cost and size of the system. In order to improve the source current waveform without adding passive components, it is necessary to reduce the source current harmonics via inverter control. However, when the inverter control reduces the source current harmonics, voltage saturation of the inverter causes source current distortion. At the rated speed and load, the voltage saturation region amounts to 40-50% of the source period, and the source current harmonics do not meet the guideline of IEC 61000-3-2. This paper proposes a direct dc-link current control (DDCCC) considering voltage saturation and the dq -axis current reference calculation for applying the DDCCC, which reduces the source current harmonics below the guideline. The effectiveness of the proposed method is verified through experiments.
Multimedia technology has been widely spread as the basis for human communications. For example, telephone, television and radio broadcasting are good tools for remote communication. Recently, communication tools such as the portable telephone and Internet spread all over the world. These devices substitute humans eyes and ears. Haptic information has paid attention as the third multimedia information. Especially a transmission technique of real-world haptic information is demanded. This paper proposes a novel haptic transmission in different motion area, named ldquomobile-haptordquo. The ldquomobilehaptordquo consists of a mobile robot and a joystick. A mobile robot has infinite area for its motion. On the contrary, a joystick is fixed for operation by a human. To transmit haptic information in the ldquomobile-haptordquo, bilateral control with dimension scaling is proposed. As a result, intuitive manipulation becomes possible by using the ldquomobile-haptordquo. Effectiveness of the proposed method is verified by experimental results.
21 July 2020 in IEEE Transactions on Industrial Electronics
The conventional force control has proposed load-side torque control based on the resonance ratio control (RRC) enhanced by an instantaneous state observer using the acceleration sensor; however, environmental stiffness variation ( $K_e$ variation) is not considered in such systems. This paper evaluates the robust stability of the conventional method based on open-loop characteristics and the stability analysis results indicate that the conventional method becomes unstable during $K_e$ variation. To realize superior high-robust stability, this paper proposes a high-robust force control based on the duality of the two-inertia system. This paper constructs an equivalent RRC (ERRC) combining the motor-side velocity control and the load-side velocity observer and demonstrates a torque-velocity duality. The results confirm that the load-side torque control based on ERRC is robust against $K_e$ variation through the analysis of open-loop characteristics, and illustrate that the ERRC the same as the conventional RRC proposed in position or velocity controls. The effectiveness of the proposed control method is validated through numerical simulations and experiments.
1 January 2013 in IEEJ Journal of Industry Applications