Rouhollah Yazdi

Rouhollah Yazdi

Auto-generated profile, based on publicly available information

Rouhollah Yazdi

Department of Civil and Mechanical Engineering, Technical University of Denmark, 2800 Kgs. Lyngby, Denmark

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 November 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
KGKapil Kumar Gupta
Kapil Kumar Gupta
RYRouhollah Yazdi
Rouhollah Yazdi
MSMathias Styrk-Geisler
Mathias Styrk-Geisler
OMOleg V. Mishin
Oleg V. Mishin
RARajan Ambat
Rajan Ambat
The paper focuses on the analysis of initiation and propagation of CO2 corrosion in several samples of low-alloy steel with different microstructures using scanning electrochemical microscopy (SECM) and other microscopy techniques. It is found that the corrosion rate and the mode of corrosion are highly sensitive to the microstructure. The overall current density is much higher and more uniformly distributed for the tempered martensite structure than for samples having either a ferritic-pearlitic microstructure or a microstructure combining ferritic, bainitic and martensitic-austenitic regions. As a result, the sample with the tempered martensite structure undergoes uniform corrosion, while the other two samples undergo selective corrosion. The SECM maps show that regions of polygonal ferrite generate larger anodic currents than the pearlitic structure in the early stages of corrosion. The residual cementite provides greater cathodic surface areas after the initial dissolution of ferritic lamellae within pearlite, promoting galvanic corrosion and subsequently enhanced dissolution of ferritic lamellae. According to SECM data, the dissolution of iron in polygonal ferritic grains is 2.4 times faster than that of ferritic lamellae in pearlitic regions.

1 March 2019 in Review of Scientific Instruments
Verified
Journal Article
Closed access
Richard BarkerRichard Barker
Richard Barker
RYRouhollah Yazdi
Rouhollah Yazdi
YHYong Hua
Yong Hua
AJAndrew Jackson
Andrew Jackson
AGAli Ghanbarzadeh
Ali Ghanbarzadeh
ANAnne Neville
Anne Neville
This paper outlines the development of an automated underwater abrasion rig to assist in understanding the galvanic interaction induced by surface films when continuous localised mechanical film breakdown is encountered on the surface of carbon steel in CO2-containing environments. The rig enables the measurement of galvanic current between a small X65 steel pin and a larger steel specimen, as well as the intrinsic corrosion rate of an additional, uncoupled larger specimen. The surface film developed on the pin is removed periodically using an automated reciprocating and rotating shaft with a sand paper grit pad attached to the base, while the surface film is allowed to establish itself undisrupted on the large specimen. The setup essentially simulates a tribo-corrosion process where local removal of material occurs within a carbon steel pipeline as a result of periodic sand particle impingement. Initial results focus on validating the reproducibility of the technique, as well as determining the galvanic effects associated with iron carbide and iron carbonate for two model sets of conditions to highlight the capabilities of the system.

12 September 2022 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
BCB. Cheraghali
B. Cheraghali
HGHamid M. Ghasemi
Hamid M. Ghasemi
MAM. Abedini
M. Abedini
RYR. Yazdi
R. Yazdi

14 May 2021 in Materials and Corrosion
Verified
Journal Article
Closed access
PDF file
GZGiorgio G. B. Zaffaroni
Giorgio G. B. Zaffaroni
VGVisweswara C. Gudla
Visweswara C. Gudla
SLSimone Laganá
Simone Laganá
CGCarsten Gundlach
Carsten Gundlach
BOBjorn Olsson
Bjorn Olsson
RARajan Ambat
Rajan Ambat