Vencislav Grabulov

Vencislav Grabulov

Auto-generated profile, based on publicly available information

Vencislav Grabulov

Društvo za unapređivanje zavarivanja u Srbiji, Grčića Milenka 67, 11000 Beograd, Srbija

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2024
Verified
Conference Paper
Closed access
DMDragan Milčić
Dragan Milčić
Miodrag MilčićMiodrag Milčić
Miodrag Milčić
Aleksija ĐurićAleksija Đurić
Aleksija Đurić
UFUniverzitet u Istočnom Sarajevu Mašinski fakultet
Univerzitet u Istočnom Sarajevu Mašinski fakultet
Damjan KlobčarDamjan Klobčar
Damjan Klobčar
BSBeograd Društvo za unapređivanje zavarivanja u Srbiji
Beograd Društvo za unapređivanje zavarivanja u Srbiji
This paper aims to compare the mechanical and structural properties of butt-welded properties of dissimilar aluminum alloys 2024-T351 and AA 6082-T6 obtained by MIG and TIG welding processes. Alloy AA 6082 T6 is well weldable by classic fusion welding processes (MIG and TIG), while alloy 2024-T351 is almost non-weldable. For the welding of these two different Al alloys, MIG and TIG welding procedures were used on 8 mm thick sheet metal using additional material 4043A (AlSi5) and a mixture of argon and helium as a protective gas for the MIG welding process, or pure argon for the TIG welding process. The paper compares the mechanical properties of welded joints obtained by MIG and TIG welding. The microstructural evolution of the welded joint of dissimilar aluminum alloys AA6082-T6 and AA2024-T351 is compared. The mechanical properties of welded joints of dissimilar aluminum alloys are compared based on the results of Vickers hardness tests, tensile and bending tests of welded samples.

15 March 2026 in Zavarivanje i zavarene konstrukcije
Verified
Journal Article
Closed access
DMDragan Milčić
Dragan Milčić
Miodrag MilčićMiodrag Milčić
Miodrag Milčić
Aleksija ĐurićAleksija Đurić
Aleksija Đurić
Damjan KlobčarDamjan Klobčar
Damjan Klobčar
NZNataša Zdravković
Nataša Zdravković
VGVencislav Grabulov
Vencislav Grabulov
This paper aims to compare the mechanical and structural properties of butt-welded joints of dissimilar Al alloys 2024-T351 and AA 6082-T6 obtained by MIG and TIG welding processes. Alloy AA 6082 T6 is weldable by classic fusion welding processes (MIG and TIG), while alloy 2024-T351 is mostly non-weldable. For the welding of these two different Al alloys, MIG and TIG welding procedures were used on 8 mm thick sheet metal using additional material 4043A (AlSi5) and a mixture of Ar and He as a shielding gas for the MIG welding process, or pure Ar for the TIG welding process. The present study showcases the mechanical properties of welded joints obtained by MIG and TIG welding. The microstructural evolution of the welded joint of dissimilar Al alloys AA6082-T6 and AA2024-T351 is compared. The mechanical properties of welded joints of dissimilar Al alloys are estimated based on the results of Vickers hardness, tensile, and bending tests of as-welded samples.

15 September 2025 in Zavarivanje i zavarene konstrukcije
Verified
Journal Article
Closed access
BGBojan Rade Gligorijević
Bojan Rade Gligorijević
VGVencislav Grabulov
Vencislav Grabulov
EREndre Romhanji
Endre Romhanji
The present study examined the effect of heat input and T6 post-weld heat treatment on the microstructure, electrical conductivity, and intergranular corrosion of AA6026/AA5183/AA6026 welded joints. The samples were welded using pulsed MIG, pulsed TIG, and combined TIG&MIG procedures, and a portion of samples was subjected to the T6 condition (solution annealing, water quenching, and artificial aging). The results showed that lower heat input (pulsed MIG) reduced intermetallic precipitation along grain boundaries and thereby improved resistance to intergranular corrosion, while higher heat input (pulsed TIG) promoted more intensive precipitation and increased the risk of corrosion. The T6 treatment partially homogenized the microstructure but also likely promoted the precipitation of Mg₂Si along grain boundaries in the heat-affected zone of AA6026 and the formation of continuous β-Al₃Mg₂ films along grain boundaries in the weld metal of AA5183, which together increased susceptibility to intergranular corrosion of welded joints. The best resistance to intergranular corrosion was observed in joints produced by pulsed MIG welding with low heat input, while TIG&MIG joints, owing to even lower heat input, maintained stable intergranular corrosion resistance even after T6 treatment. In contrast, joints obtained by pulsed TIG welding with higher heat input suffered the most severe degradation of intergranular corrosion resistance in the T6 condition. These findings confirmed that heat input control was the decisive factor governing microstructural changes, electrical conductivity, and corrosion behavior of AA6026/ER5183/AA6026 welded joints.

1 January 2026
Verified
Conference Paper
Open access
BGBojan Rade Gligorijević
Bojan Rade Gligorijević
VMVeljko Milašinović
Veljko Milašinović
SDStefan Dikić
Stefan Dikić
VGVencislav Grabulov
Vencislav Grabulov
The increasing use of aluminum conductors while retaining copper terminals has increased the need for reliable Al/Cu transitions. Mechanical connectors remain practical, but their long-term performance depends on stable pressure-controlled contact despite oxidation, corrosion, thermal expansion mismatch, creep, stress relaxation, and fretting. Metallurgical transitions reduce this dependence. Continuous-drive friction welding (CDFW) is particularly attractive for cylindrical components because it is rapid, filler-free, and avoids bulk melting. This review relates CDFW parameters to material transfer, interface morphology, recrystallization, intermetallic-compound (IMC) formation, radial heterogeneity, electrical behavior, mechanical properties, fracture, and thermal exposure. Insufficient heat input produces incomplete bonding, whereas excessive heat input promotes softening, material loss, and IMC growth. Optimized short-cycle CDFW can produce complete bonding with approximately 0.5 μm Al₂Cu while retaining more than 92% of the theoretical Al/Cu conductivity and approximately the tensile strength of the Al base material. However, IMC thickness alone cannot describe joint integrity because phase composition, continuity, residual stress, radial distribution, and adjacent microstructure also influence fracture. Future development should therefore focus on phase-specific, spatially resolved, and service-life-oriented interface engineering.