Utku Soylu

Utku Soylu

Auto-generated profile, based on publicly available information

Utku Soylu

Department of Electrical and Computer Engineering, University of California at Santa Barbara, Santa Barbara, CA, USA

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 July 2023 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
USUtku Soylu
Utku Soylu
AAAmirreza Alizadeh
Amirreza Alizadeh
MSMunkyo Seo
Munkyo Seo
MRMark J. W. Rodwell
Mark J. W. Rodwell
We report 280 GHz 8:1 and 16:1 frequency multipliers in 250-nm indium phosphide (InP) HBT technology. The 8:1 multiplier uses three cascaded push-push emitter-coupled-pairs serving as balanced frequency doublers, with 1:1 transformers at 35, 70, and 140 GHz providing single-ended to differential conversion; the 16:1 multiplier has an additional input emitter-coupled push-push doubler whose drive signal is generated by a transistor differential input stage. With $-\text{2}$ dBm input power, the 8:1 multiplier generates $-\text{0.6}$ dBm output power at 280 and has 48-GHz $\text{3}$ -dB bandwidth. Spurious harmonics are suppressed by ${>} 28$ dBc over the $\text{3}$ -dB bandwidth. With $-\text{13}$ dBm input power, the 16:1 multiplier generates $-\text{0.6}$ dBm output power at 280 and has 44-GHz $\text{3}$ -dB bandwidth. Spurious harmonics are suppressed by ${>} 26$ dBc over the $\text{3}$ -dB bandwidth. The 8:1 and 16:1 multipliers consume 102-and 162-mW dc power and occupy 0.4-and 0.75-mm 2 die area, respectively. To the authors’ knowledge, these results demonstrate record spectral purity for frequency multiplier chains operating near 280 GHz.

9 September 2024 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
AAAmirreza Alizadeh
Amirreza Alizadeh
USUtku Soylu
Utku Soylu
LWLogan Whitaker
Logan Whitaker
BSBiljana Stamenic
Biljana Stamenic
DJDemis D. John
Demis D. John
MRMark J. W. Rodwell
Mark J. W. Rodwell
We report planar 200-GHz transmitter and receiver modules for high-frequency, high-capacity wireless transmission. The modules were used for 8-Gbaud 16QAM data transmission (32 Gb/s) over 7.1 m, featuring 13.4% rms EVM on a link with 10.4-dB added attenuation. The modules are compact and highly integrated, with only a passive antenna substrate and a single transmitter or receiver integrated circuit (IC) providing the transmitter and receiver radio frequency (RF) front-end functions, avoiding the size and cost of machined waveguide interfaces. The transmitter module contains a single indium phosphide (InP) IC, with ( I , Q ) baseband inputs, frequency up-conversion, and a power amplifier (PA), and it is wire-bonded using a wedge-bonder to a passive fused-silica (FS) antenna substrate that carries a 2 $\times$ 2 patch antenna array and an impedance-matching network that matches the transmitter IC to the combined impedances of the antenna array and the IC–antenna wire-bond. The antenna radiation pattern has a beamwidth designed to couple efficiently to external polytetrafluoroethylene (PTFE) lenses having a 0.56 numerical aperture. The receiver module is similar. The transmitter module has a measured $\pm$ 25 $^\circ$ beamwidth in the E -plane and H -plane, a measured peak equivalent isotropic radiated power (EIRP) of 24 dBm, with the EIRP remaining greater than 19 dBm over 200–218 GHz. The receiver module has 29.4-dB peak conversion gain with 3-dB bandwidth of 14 GHz (from 194 to 208 GHz).

1 November 2019
Verified
Conference Paper
Closed access
JSJonathan P. Sculley
Jonathan P. Sculley
BMBrian Markman
Brian Markman
USUtku Soylu
Utku Soylu
YFYihao Fang
Yihao Fang
MUMiguel E. Urteaga
Miguel E. Urteaga
PYPaul D. Yoder
Paul D. Yoder
We report Monte Carlo simulation results of 300nm InP heterojunction bipolar transistors driven to exhibit distortion. IM3 distortion is typically explained by collector velocity modulation. Full-band ensemble Monte Carlo simulations implicate intervalley transfer as an additional source of distortion under conditions of high current, low voltage, and high doping. Simulations reveal that intervalley transfer promotes the formation of traveling accumulation domains which result in high frequency distortion more significant than that caused by velocity modulation. Special care must be taken when designing high current HBT power amplifiers in order to mitigate this effect.