Marisa Moreno-Ríos

Marisa Moreno-Ríos

Auto-generated profile, based on publicly available information

Marisa Moreno-Ríos

Postgraduate Studies and Research, Technological Institute of Pachuca, Avenue Felipe Ángeles Km. 84.5 Venta Prieta, Pachuca de Soto, 42083, State of Hidalgo, Mexico

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2011 in Wear
Verified
Journal Article
Closed access
MVManuel Vite-Torres
Manuel Vite-Torres
MMM. Moreno-Ríos
M. Moreno-Ríos
EHE.A. Gallardo Hernández
E.A. Gallardo Hernández
JLJ.R. Laguna-Camacho
J.R. Laguna-Camacho

29 May 2014 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Verified
Journal Article
Open access
MMMarisa Moreno-Ríos
Marisa Moreno-Ríos
EGEzequiel A Gallardo-Hernández
Ezequiel A Gallardo-Hernández
MVManuel Vite-Torres
Manuel Vite-Torres
APAlejandro Peña-Bautista
Alejandro Peña-Bautista
The aim of this work was to prove that the oil applied to the wheel flange using on-board lubricators not only alters the friction coefficient between wheel and rail but also influences the braking and acceleration performance of trains on one of the lines of the metro in Mexico City. A series of tests were carried out in the presence of an oil lubricant, both in the laboratory and in the field, using a pendulum tester. It was observed that the oil migrated from the rail corner to the top of the rail. In another set of experiments, water was sprayed onto the lubricant on the top of the rail. The results indicated that under these conditions, the friction coefficient has a low value in rail sections where a high value of the friction coefficient is required. Tests with water/oil mixtures presented similar levels of friction to the oil-only tests. A set of tests were performed after the rail surface was cleaned and the oil lubricant and water were applied together. The laboratory and field tests showed similar behaviour trends for the friction coefficient. The pendulum method can be used to assess railhead friction on short-length sections of rail. Points are made regarding the conditioning of the pads and calibration of the pendulum arm.

1 January 2026 in International Journal of Dentistry
Verified
Journal Article
Open access
JRJosé Reyes-Gasga
José Reyes-Gasga
MMMarisa Moreno-Rios
Marisa Moreno-Rios
Arturo Rodríguez-GómezArturo Rodríguez-Gómez
Arturo Rodríguez-Gómez
EBEtienne Bres
Etienne Bres
We examine the image contrasts presented at micrometric and nanometric scales of the scanning electron microscope (SEM), transmission electron microscope (TEM), scanning transmission electron microscope (STEM), and atomic force microscope (AFM) in the tapping mode, looking for the observation of the central feature known as “the central dark line” (CDL) in the structure of human tooth enamel crystals. Since our interest is in inorganic material, mainly at the nanometric scale, the enamel samples for SEM and AFM were polished following a metallographic procedure, using progressively finer silicon carbide papers and etching with orthophosphoric acid. For TEM and STEM, the samples were produced by the focused ion beam (FIB) technique. The CDL images were well recorded using TEM and STEM, but not in SEM and AFM images. SEM images revealed the size and morphology of the enamel crystals, while AFM images revealed spherical and band‐like structures. The observation of the CDL using TEM and STEM suggests that it may represent a potential chemical compositional site.

1 January 2008
Verified
Conference Paper
Closed access
PDF file
IHI. Hilerio
I. Hilerio
MVManuel Vite-Torres
Manuel Vite-Torres
MMM. Moreno
M. Moreno
MBM. A. Barron
M. A. Barron
HJH. Jime´nez
H. Jime´nez
BVB. Vazquez
B. Vazquez
Chromium Nitride (CrN) thin films were deposited on AISI steel 316 substrates by means of the reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a DC source. For the second coating a negative substrate bias voltage was applied. X ray diffraction, quantitative energy dispersion and scanning electron microscope were employed to characterize the two different phases, their chemical composition as well as their microstructure. In addition, a microhardness test was carried out. The results show that a better phase formation of CrN thin films was achieved when a heating source was present (first case). Both coatings presented homogeneous surface. Their compositions show differences even when the gases flowing are the same in composition. Regarding to the hardness test results, there can be found a higher value when using a heating source.

5 July 2025
Verified
Journal Article
Closed access
Eduardo Colin GarcíaEduardo Colin García
Eduardo Colin García
ACAlejandro Cruz-Ramírez
Alejandro Cruz-Ramírez
Ricardo Gerardo Sánchez AlvaradoRicardo Gerardo Sánchez Alvarado
Ricardo Gerardo Sánchez Alvarado
MMMarisa Moreno-Ríos
Marisa Moreno-Ríos

5 October 2023 in Tópicos de Investigación en Ciencias de la Tierra y Materiales
Verified
Journal Article
Open access
PDF file
DLDiana Cuautle Lezama
Diana Cuautle Lezama
APArmando Irvin Martinez Perez
Armando Irvin Martinez Perez
ECEdgar Ernesto Vera Cardenas
Edgar Ernesto Vera Cardenas
MRMarisa Moreno Ríos
Marisa Moreno Ríos
JMJesús Mendoza
Jesús Mendoza
Una de principales causas de un desempeño mecánico deficiente en máquinas industriales, es la mala selección y calidad de los lubricantes, esto se deriva a la falta de comprensión de sus propiedades tribológicas. Por esta razón es importante complementar la información fisicoquímica de los lubricantes con los resultados de los ensayos tribológicos impactando directamente a la productividad y la eficiencia de los procesos industriales. Para determinar las propiedades tribológicas de lubricantes, en este trabajo se presenta el diseño conceptual de una plataforma de 4 bolas bajo las especificaciones de la norma ASTM D2266. Se aplicó la metodología de diseño de Nigel Cross, la cual aporta resultados para satisfacer las subfunciones requeridas y objetivos establecidos. El diseño conceptual se validó numéricamente con el software ANSYS, a partir del análisis de esfuerzos y deformaciones del bastidor, la sujeción de la bola y de la celda, manifestando la importancia del material aplicado al sistema para evitar fallas durante la operación.