1 January 2023 in Physics of Fluids
The application of drag reduction tech holds great significance to energy saving. To achieve better drag reduction, we investigated the flow characteristics of the turbulent boundary layer (TBL) over a composite surface made of sawtooth riblets with superhydrophobic coat (rib&SHS), a superhydrophobic surface (SHS), and a smooth surface using particle image velocimetry. The results showed that the drag reduction rate of the composite surface was higher than that of the superhydrophobic surface at the same Reynolds number. When the Reynolds number reached 2015, the drag reduction effect of SHS was almost ineffective (drag reduction was only 1.2%), whereas rib&SHS maintained satisfactory results (drag reduction was 20.2%). By proper orthogonal decomposition (POD), the second-order POD mode showed the tilt angles of the interface of Q2 and Q4 events inside the TBL over rib&SHS, and SHS were reduced compared with the smooth surface in the drag reduction cases. With drag reduction of rib&SHS and SHS, the hairpin vortexes were lifted away from the wall and the distances of vortexes within hairpin vortex packets decreased. Compared with SHS, rib&SHS had a greater effect on hairpin vortexes and hairpin vortex packets because the riblets made the Q2 events of rib&SHS weaker than that of SHS. So, the rib&SHS has a higher drag reduction rate and a larger drag reduction Reynolds number range than the SHS. It can be used to guide the drag reduction design of underwater vehicles.
1 April 2024 in Physics of Fluids
Energy conservation and environmental protection have become pivotal components of the green economy. In recent years, underwater drag reduction technology has garnered significant interest. This study discusses a novel composite surface that combines divergent riblets with a superhydrophobic coating (D-rib&SHS) to enhance the drag reduction rate. Alongside this new surface, a riblet surface with a superhydrophobic coating (rib&SHS, without yaw angles) and a smooth surface are used as comparison groups. The turbulent boundary layer flow of these three surfaces is measured using a two-dimensional particle image velocimetry system. The results indicated that the maximum drag reduction rate of D-rib&SHS is approximately 27% higher than that of rib&SHS, and the drag reduction range is increased to Reθ≈4100 compared to rib&SHS (Reθ≈2200). Using correlation algorithms, it observed that the spacing between low-speed streaks over D-rib&SHS is larger than that of rib&SHS and the smooth surface. This finding suggested that the spacing between the hairpin vortex legs of D-rib&SHS is wider. The increased spacing between the hairpin vortex legs reduces the likelihood of vortex head formation between the two quasi-streamwise vortices, ultimately suppressing the auto-generation of hairpin vortices. Consequently, the development of hairpin vortex packets over D-rib&SHS is also inhibited. These phenomena observed over D-rib&SHS can be attributed to the combined effects of velocity slip on the superhydrophobic coating and the secondary flow over the divergent riblets near the wall. In addition, unlike divergent riblets that are not covered with a superhydrophobic coating, where the drag reduction effect is more pronounced with a yaw angle of 30° compared to 10°, D-rib&SHS with a 10° yaw angle demonstrated a superior drag reduction effect compared to D-rib&SHS with a 30° yaw angle. This innovative composite surface enhances the drag reduction effect and expands the drag reduction Reynolds number range, offering a new approach to mitigating drag in turbulent boundary layer flows.
1 July 2026 in Physics of Fluids
To reveal the physical mechanisms governing precise flow control during unsteady aquatic maneuvers, this study investigates the vortex shedding dynamics of maneuvering zebrafish using time-resolved particle image velocimetry. We identify a significant kinematic phase lag in active body deformation, where the moment of maximum bending distinctly lags behind the moment of maximum tail-beat amplitude. Based on this kinematics, we establish a spatiotemporal decoupling framework for vortex prediction. Spatially, a “head-steering” geometric criterion is discovered, exhibiting a strong linear correlation (R2 = 0.94) between the initial head orientation and the wake topology orientation. This implies that the head acts as a “geometric rudder,” pre-determining the symmetry-breaking direction of the wake regardless of the subsequent body undulation. Temporally, the non-dimensional vortex shedding timing demonstrates independence from the Reynolds number (Re = 300–1600). This robustness confirms that, despite the laminar nature of the flow, the shedding process is insensitive to Reynolds number variations, indicating that viscous effects play a secondary role in determining the shedding timing. This validates the applicability of universal inertial scaling laws (i.e., Strouhal number scaling). Furthermore, by introducing an “equivalent rectangular bluff-body” hypothesis, we demonstrate that the active tail sweep amplitude (A) functions as the transverse blockage width (short side), while the body length (L) acts as the streamwise chord (long side). Consequently, a modified Strouhal number scaling law, governed by the effective aspect ratio (L/A), successfully predicts the shedding frequency of actively deforming fish. These findings suggest that complex biological maneuvering wakes are governed by low-dimensional kinematic scaling laws, providing an empirical model for simplifying control strategies.