Aida Lutsenko

Aida Lutsenko

Auto-generated profile, based on publicly available information

Aida Lutsenko

Department of Chemistry and Chemical Technology, Manash Kozybayev North Kazakhstan University, Petropavlovsk 150000, Kazakhstan

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2022 in Polymers
Verified
Journal Article
Open access
PDF file
ADAntonina Dyuryagina
Antonina Dyuryagina
ALAida Lutsenko
Aida Lutsenko
KOKirill Ostrovnoy
Kirill Ostrovnoy
VTVitaliy Tyukanko
Vitaliy Tyukanko
ADAlexandr Demyanenko
Alexandr Demyanenko
MAMeiramgul Akanova
Meiramgul Akanova
This article presents the results of studying the disaggregation of titanium dioxide in water-dispersion compositions based on an acrylic film-forming agent under the action of a surfactant. The possibility of using polyether siloxane copolymer (PC) and sodium polyacrylate (NaPA) in paint and varnish compositions as modifying additives of the dispersing effect is proved. The correlation between the dispersing effect of surfactants and the amount of their adsorption on the pigment is proved. NaPA, which provides a greater reduction in adsorption strength, demonstrates a greater dispersing effect than PC. It was found that the larger the size of the aggregates of pigment particles, the greater the disjoining pressure created by the surfactant. An equation is derived that generalizes the cumulative contribution of surfactant concentration and the content of the film-forming agent in suspensions to the average particle diameter of pigment. The introduction of NaPA in the amount of 0.25 g/dm3 into the paint allows the rate of acid corrosion to be reduced by 2 times, the number of pores in the coating to be decreased, and the adhesion of the coating to be significantly increased (by 2 points according to ISO 11845: 2020).

11 May 2024 in Polymers
Verified
Journal Article
Open access
PDF file
ADAntonina Dyuryagina
Antonina Dyuryagina
YBYuliya Byzova
Yuliya Byzova
KOKirill Ostrovnoy
Kirill Ostrovnoy
ADAlexandr Demyanenko
Alexandr Demyanenko
VTVitaliy Tyukanko
Vitaliy Tyukanko
ALAida Lutsenko
Aida Lutsenko
The purpose of these studies was to establish the influence of the microstructural and rheological characteristics of modified bitumen compositions on the strength indicators of asphalt concrete. The effect of additives concentration on the rheological characteristics and microstructure of binary “bitumen–surfactant”, “bitumen-AG-4I”, and ternary “bitumen-AG-4I-AG-4I” systems has been studied. To assess the effect of bitumen dispersion on the physical and mechanical characteristics of modified asphalt concrete samples, the compressive strength value was determined. The following chemicals have been used as additives: the original product AS-1, industrial additive AMDOR-10, and used sealant AG-4I, a product based on polyisobutylene and petroleum oils. At an increased content of AG-4I (C ≥ 1.0 g/dm3) in ternary systems, the contribution of the emerging intermolecular polyisobutylene network to the development of structuring processes increases while the viscous effect of the surfactant AS-1 decreases. It has been established that the minimum size of bee-like bitumen structures (1.66 µm) is recorded with the joint presence of additives in the bitumen, AS-1 at a level of 1.0 g/dm3 and AG-4I at a level of 1.0 g/dm3. Under the same concentration regimes of the ternary bitumen composition, the maximum increase in compressive strength RD was achieved with the smallest size of bee-like structures of modified bitumen.

3 October 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ADAntonina Dyuryagina
Antonina Dyuryagina
YBYuliya Byzova
Yuliya Byzova
KOKirill Ostrovnoy
Kirill Ostrovnoy
ALAida Lutsenko
Aida Lutsenko
Improving the durability of asphalt concrete road surfaces by increasing their moisture resistance is an urgent task. Modified bituminous binders should be compacted into coatings with the lowest possible water saturation. The purpose of this study was to establish the effect of modifiers on the hydrophobicity of bituminous films in order to achieve minimum water saturation and to build a mathematical model of the wetting process with water. As modifiers, we used a product of amination of distillation residues of petrochemistry, waste sealing liquid (a solution of high molecular weight polyisobutylene in mineral oil), and a condensation product of polyamines and higher fatty acids. The water-repellent effect of modifiers was studied by measuring the contact angle of bituminous film with a water drop. The water saturation of asphalt concrete samples was determined by the amount of water absorbed by asphalt concrete at 20 °C. A close correlation was revealed between the hydrophobicity of modified bitumen and the water saturation of asphalt concrete. Generalized equations and a graphical representation of a function of several variables allowed for optimizing compositions by the content of modifiers to achieve the required performance properties of asphalt concrete coatings.

14 January 2025 in Polymers
Verified
Journal Article
Open access
PDF file
ADAntonina Dyuryagina
Antonina Dyuryagina
ADAlyona Degert
Alyona Degert
YBYuliya Byzova
Yuliya Byzova
KOKirill Ostrovnoy
Kirill Ostrovnoy
ADAlexandr Demyanenko
Alexandr Demyanenko
TSTatyana Valerievna Shirina
Tatyana Valerievna Shirina
The aim of the work was to study the effect of additive concentration on changes in the adhesive and cohesive strength of bitumen. To evaluate the effectiveness of modifiers in the composition of binary and triple bitumen systems in relation to mineral fillers of two grades, the method of determination of the adhesive efficiency and thermodynamic calculations of adhesion and cohesion work were used. The following compounds were used as additives: AS-2 synthesized from the oil refining waste and AG-4I (waste sealing liquid). Adhesion–cohesion processes in modified bitumen systems are limited by the wetting effect of crushed stone and the intensity of intermolecular forces in the condensed phase of the binder. In the binary compositions, the addition of modifiers into bitumen significantly improves the cohesive strength and adhesive efficiency in relation to crushed stone. The introduction of AS-2 into bitumen compositions with AG-4I increases adhesion efficiency and thermodynamic work of adhesion in relation to the filler surface. The adhesion efficiency and thermodynamic work of adhesion in the “bitumen-AG-4I-AS-2” system reach their maximum at CAG-4I = 3.0 g/dm3 and CAS-2 = 1.5 g/dm3. In these concentration modes, the composition ensures maximum increase in adhesion efficiency (AKS = 65.18%; AKA = 48.11%) and the greatest increase in thermodynamic work of adhesion (WA(KS) = 15.79 mN/m; WA(KA) = 14.13 mN/m).

28 April 2025 in Bulletin of the Tomsk Polytechnic University Geo Assets Engineering
Verified
Journal Article
Open access
PDF file
DODarya Yu. Ostrovnaya
Darya Yu. Ostrovnaya
ADAntonina Dyuryagina
Antonina Dyuryagina
KOKirill Ostrovnoy
Kirill Ostrovnoy
ALAida A. Lutsenko
Aida A. Lutsenko
Relevance. When processing wood, up to 40% of waste is generated, which includes shavings, sawdust, wood dust, bark parts and substandard wood of various shapes and sizes. Secondary wood waste contains lignin, which is a source for the production of salts of lignosulfonic acids – lignosulfonates. The possibility of using these compounds as pigment dispersants is due to the amphiphilic structure of their molecules. The targeted synthesis of lignosulfonates from secondary wood waste, on the one hand, solves the problems of ensuring waste-free production, and on the other hand, obtaining a marketable product with dispersing properties. Aim. Optimization of the method for obtaining a water-soluble dispersant from wood waste. Methods. Probabilistic deterministic method of experiment planning, spectrophotometry method, computer microscopy method. Results and conclusions. The paper shows the possibility of targeted synthesis of lignosulfonate LSs from birch sawing waste. Optimization of synthesis modes was carried out using probabilistic-deterministic planning methods and a generalized model was obtained that allows estimating the yield of lignosulfonate. The authors studied the effect of three modifiers on the dispersion of titanium dioxide in aqueous acrylic enamel. It is shown that the introduction of LSs, LSt and Dispers 715w at the level of 1.0–0.5 g/dm3 leads to a finer dispersion of the pigment. The best dispersion indicators are observed at a LSs content of 0.5 g/dm3, while the average diameter decreases by 3.1 times (from 8.4 to 2.6 microns). With the content of synthesized LSs at the level of 1.0 g /dm3 in a water-acrylic paint coating, the degree of protection of steel in sulfuric acid solutions was at least 62%.