22 March 2020 in Vehicle System Dynamics
Active steering technology is an effective method to solve the contradiction between curving performance and running stability of traditional bogie. In this study, an integrated active steering device was developed to integrate wheelset constraints and actuators. In addition, to study the minimum wear number control strategy, the existence of an optimal steering level that minimises the wear number was corroborated by a theoretical derivation based on the single wheelset model. Later, this research method was extended to the complete vehicle lateral dynamics model and steady-state solutions at different active steering levels were analysed. The results demonstrate that at optimal steering control, wear number is the lowest. This state is less affected by the running velocity, stiffness of the primary suspension, tread taper, and creep state, which are determined by the wheelbase and track curvature. The lateral forces of rail-vehicle wheels with an active steering function at different steering levels were measured using instrumented wheelsets. Furthermore, the accuracy of the simulation model was verified by comparing the experimental data with simulation results. Finally, the wear number of test vehicles at different steering levels were predicted using this model, and the control strategy proposed in this investigation was validated.
10 February 2020 in Vehicle System Dynamics
Active radial technology can effectively improve the curving performance of rail vehicles. The curvature of track is the key parameter of active radial system. In order to acquire this parameter in real time, a new method of curvature measurement based on secondary suspension rotation angle sensing is proposed in this paper. It is proved that this scheme can measure the curvature with small error and high synchronisation by theoretical deduction and simulation. Then, based on the curvature measurement scheme, an active radial system for rail vehicles is proposed, with emphasis on the design of an integrated device for wheelset constraints and actuator. Subsequently, the physical model of the actuator is established, and its dynamic response characteristics under typical working conditions are determined. Finally, the effect of the active radial technology of railway vehicles based on secondary suspension rotation angle sensing is analysed by the whole vehicle dynamic model with active radial function. The results show that the curvature measurement scheme is feasible, the curving performance of a rail vehicle under active radial control is improved significantly, and the thrust of the actuator is low. The research results can provide an engineering reference for real-time curvature measurements and active radial systems.
27 March 2022 in Vehicle System Dynamics
In this study, dynamic models of three bogies— traditional bogie (TB), active steering bogie (ASB), and forced steering bogie (FSB) —were established to clarify the similarities and differences between them in the parameter optimization design of dynamic performance. The first- and second-order sensitivities of the effects of the vehicle dynamic parameters on the wear, running stability, and riding comfort were obtained based on the global sensitivity method. According to the results of sensitivity analysis, the ASB and FSB primarily focus on changing the steering mechanism of the TB in the curved track and have insignificant effect on the running stability and riding comfort. Next, the dynamic performances of the three vehicles were evaluated using the control variable method. The results indicate that the ASB and FSB could change the parameter optimization method of TB, mainly because the contradiction between wear and running stability need not be considered when key parameters are in the feasible region, and the optional range of parameters is further widened. Finally, parameter optimization methods for different vehicles were formulated based on a comprehensive dynamic performance function.
31 July 2023 in IEEE Transactions on Vehicular Technology
Active steering control can significantly improve the curving performance of rail vehicles. However, it is constrained by the traction and braking of bogie. In this study, methods for optimizing and distributing active steering control quantities under constrained conditions are investigated. First, the wear number of the wheelset is set as the objective function. A controller is developed in the control layer based on a linearized bogie model with the wear number as the cost function using the model predictive control method. Then, the system state is observed using a Kalman filter with actuator feedback; the wheelset force state is also estimated using the actuator feedback. Subsequently, the optimum wheelset yaw angle under the constraints is solved. In the distribution layer, the spread of actuator displacements under traction and braking conditions is achieved by combining the longitudinal force coordination equations for the wheelset. The simulation results showed that the full utilization of the overdrive characteristics of the two coaxial actuators enabled the redistribution of actuator displacement commands under traction and braking conditions without reducing steering efficiency. Moreover, the maximum load on the actuators was effectively reduced. Finally, the parametric robustness of the controller was examined. The results showed that the controller and observer had good parametric robustness owing to the attitude stability of the bogie after active steering control was implemented.
1 June 2023 in Vehicle System Dynamics
26 April 2022 in Vehicle System Dynamics
Active steering technology can effectively solve the contradiction between the running stability and curving performance of traditional bogies. However, the execution deviations between the actual and theoretical steering actions, which expressed in this paper as equivalent curvature differences, would occur when mileage error or other abnormal operating conditions happens. In this study, the influence of equivalent curvature differences on running safety was studied, and a steering efficiency evaluation method was proposed. First, the equivalence between the wheel–rail relationship in the under- and over-steering states and that in the passive state was demonstrated by combining analytical and numerical simulation methods. It was concluded that under- and over-steering states do not worsen the running safety of rail vehicles. Then, the formula for wear number with the equivalent curvature difference as the independent variable was derived based on the linear model of the rail vehicle, and the accuracy of the formula was verified using the nonlinear model. Finally, a steering efficiency evaluation method was established, and a steering efficiency evaluation under different equivalent curvature differences and steering rates was conducted. The results of this study can provide a reference for engineering active steering systems.