Chao Liu

Chao Liu

Auto-generated profile, based on publicly available information

Chao Liu


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2019 in Nanomaterials
Verified
Journal Article
Open access
PDF file
JLJianlin Luo
Jianlin Luo
SCShuaichao Chen
Shuaichao Chen
QLQiuyi Li
Qiuyi Li
CLChao Liu
Chao Liu
SGSong Gao
Song Gao
JGJunbing Guo
Junbing Guo
There is a constant drive to improve the properties of recycled concrete owing to its inferior strength and fracture toughness compared to normal concrete and recent progress in graphene oxide (GO) nanomaterials impelling nanosized reinforcements to recycled concrete. Here, GO-modified natural sand (NS)- or recycled sand (RS)-based mortars (GONMs or GORMs) with six GO fractions (wGOs) were fabricated to explore their 28 d mechanical strengths (f28t, f28c), fracture toughness (KIC, δc), and microhardness (Hv), as well as their crystal phases (using X-ray powder diffraction) and microstructures (using scanning electronic microscopy). Results reveal, greater enhancements in mechanical strengths (4.50% and 10.61% in f28t, 4.76% and 13.87% in f28c), fracture toughness (16.49% and 38.17% in KIC, 160.14% and 286.59% in δc), and microhardness (21.02% and 52.70% in Hv) of GORM with just 0.025 wt‰ and 0.05 wt‰ GO, respectively, with respect to the control are achieved when comparing with those of GONM with the same wGO. More zigzag surfaces, more irregular weak interface slips, and the relatively lower strengths of RS bring the superiority of the template and reshaping effects of GO into full play in GORM rather than in GONM. These outcomes benefit a wide range of applications of recycled concrete products.

25 March 2019 in Materials
Verified
Journal Article
Open access
PDF file
CLChao Liu
Chao Liu
JLJianlin Luo
Jianlin Luo
JLJianlin Luo
Jianlin Luo
SGSong Gao
Song Gao
ZJZUQUAN JIN
ZUQUAN JIN
SCShuaichao Chen
Shuaichao Chen
Prefabricated building development increasingly requires foam concrete (FC) insulation panels with low dry density (ρd), low thermal conductivity coefficient (kc), and a certain compressive strength (fcu). Here, the foam properties of a composite foaming agent with different dilution ratios were studied first, high-belite sulphoaluminate cement (HBSC)-based FCs (HBFCs) with 16 groups of orthogonal mix proportions were subsequently fabricated by a pre-foaming method, and physical properties (ρd, fcu, and kc) of the cured HBFC were characterized in tandem with microstructures. The optimum mix ratios for ρd, fcu, and kc properties were obtained by the range analysis and variance analysis, and the final optimization verification and economic cost of HBFC was also carried out. Orthogonal results show that foam produced by the foaming agent at a dilution ratio of 1:30 can meet the requirements of foam properties for HBFC, with the 1 h bleeding volume, 1 h settling distance, foamability, and foam density being 65.1 ± 3.5 mL, 8.0 ± 0.4 mm, 27.9 ± 0.9 times, and 45.0 ± 1.4 kg/m3, respectively. The increase of fly ash (FA) and foam dosage can effectively reduce the kc of the cured HBFC, but also leads to the decrease of fcu due to the increase in mean pore size and the connected pore amount, and the decline of pore uniformity and pore wall strength. When the dosage of FA, water, foam, and the naphthalene-based superplasticizer of the binder is 20 wt%, 0.50, 16.5 wt%, and 0.6 wt%, the cured HBFC with ρd of 293.5 ± 4.9 kg/m3, fcu of 0.58 ± 0.02 MPa and kc of 0.09234 ± 0.00142 W/m·k is achieved. In addition, the cost of HBFC is only 39.5 $/m3, which is 5.2 $ lower than that of ordinary Portland cement (OPC)-based FC. If the surface of the optimized HBFC is further treated with water repellent, it will completely meet the requirements for a prefabricated ultra-light insulation panel.

7 September 2018 in Sensors
Verified
Journal Article
Open access
PDF file
JLJianlin Luo
Jianlin Luo
CZChunwei Zhang
Chunwei Zhang
LLLu Li
Lu Li
BWBaolin Wang
Baolin Wang
QLQiuyi Li
Qiuyi Li
CLChao Liu
Chao Liu
Lead-zirconate-titanate (PZT) nanoscale powder was first synthesized by the sol-gel method, then PZT and 0–3 type PZT/chrysotile fiber (CSF)/cement composite (PZTCC) wafers were fabricated after grind-mixing PZT powder with strontium carbonate and/or cement, ductile CSF in tandem with press-sintered process, respectively. The crystal structure (XRD), microstructure (SEM), piezoelectric properties after surface silver penetration, and polarization of the PZT and PZTCC wafer were investigated. Furthermore, self-sensing responses under either impulse or cyclic loading and micro-hardness toughness of PZTCC were also investigated. Results show that the incorporation of CSF and cement admixture weakens the perovskite crystalline peak of PZTCC; reduces the corresponding piezoelectric coefficient from 119.2 pC/N to 32.5 pC/N; but effectively bridges the gap on the toughness between PZTCC and concrete since the corresponding microhardness with 202.7 MPa of PZTCC is close to that of concrete. A good linear and fast electrical response against either impulse or cyclic loading of the PZTCC is achieved with their respective sensitivity, linearity, and repeatability to 1.505 mV/N, 2.42%, and 2.11%. The sensing responses and toughness of PZTCC is encouraging as an intrinsic piezoelectric sensor for real-time health monitoring of ductile concrete structures.