1 December 2015 in Remote Sensing of Environment
Correcting for tropospheric delays is one of the largest challenges facing the interferometric synthetic aperture radar (InSAR) community. Spatial and temporal variations in temperature, pressure, and relative humidity create tropospheric signals in InSAR data, masking smaller surface displacements due to tectonic or volcanic deformation. Correction methods using weather model data, GNSS and/or spectrometer data have been applied in the past, but are often limited by the spatial and temporal resolution of the auxiliary data. Alternatively a correction can be estimated from the interferometric phase by assuming a linear or a power-law relationship between the phase and topography. Typically the challenge lies in separating deformation from tropospheric phase signals. In this study we performed a statistical comparison of the state-of-the-art tropospheric corrections estimated from the MERIS and MODIS spectrometers, a low and high spatial-resolution weather model (ERA-I and WRF), and both the conventional linear and new power-law empirical methods. Our test-regions include Southern Mexico, Italy, and El Hierro. We find spectrometers give the largest reduction in tropospheric signal, but are limited to cloud-free and daylight acquisitions. We find a ~10–20% RMSE increase with increasing cloud cover consistent across methods. None of the other tropospheric correction methods consistently reduced tropospheric signals over different regions and times. We have released a new software package called TRAIN (Toolbox for Reducing Atmospheric InSAR Noise), which includes all these state-of-the-art correction methods. We recommend future developments should aim towards combining the different correction methods in an optimal manner
10 September 2020 in Geophysical Research Letters
Measurements of present‐day surface deformation are essential for the assessment of long‐term seismic hazard. The European Space Agency's Sentinel‐1 satellites enable global, high‐resolution observation of crustal motion from Interferometric Synthetic Aperture Radar (InSAR). We have developed automated InSAR processing systems that exploit the first ~5 years of Sentinel‐1 data to measure surface motions for the ~800,000‐km2 Anatolian region. Our new 3‐D velocity and strain rate fields illuminate deformation patterns dominated by westward motion of Anatolia relative to Eurasia, localized strain accumulation along the North and East Anatolian Faults, and rapid vertical signals associated with anthropogenic activities and to a lesser extent extension across the grabens of western Anatolia. We show that automatically processed Sentinel‐1 InSAR data can characterize details of the velocity and strain rate fields with high resolution and accuracy over large regions. These results are important for assessing the relationship between strain accumulation and release in earthquakes.
24 September 2010 in Geophysical Journal International
Summary. We use InSAR and body wave modelling to determine the faulting parameters for a series of five Mw 5.9–7.1 normal faulting earthquakes that occurred du
5 September 2009 in Geophysical Research Letters
We use InSAR and body‐wave seismology to determine independent source parameters for the 6th April 2009 Mw 6.3 L'Aquila earthquake and confirm that the earthquake ruptured a SW‐dipping normal fault with ∼0.6–0.8 m slip. The causative Paganica fault had been neglected relative to other nearby range‐frontal faults, partly because it has a subdued geomorphological expression in comparison with these faults. The L'Aquila earthquake occurred in an area with a marked seismic deficit relative to geodetically determined strain accumulation. We use our source model to calculate stress changes on nearby faults produced by the L'Aquila earthquake and we find that several of these faults have been brought closer to failure.
19 December 2016 in Journal of Geophysical Research: Solid Earth
The North Anatolian Fault (NAF) is a major tectonic feature in the Middle East and is the most active fault in Turkey. The central portion of the NAF is a region of Global Navigation Satellite Systems (GNSS) scarcity. Previous studies of interseismic deformation have focused on the aseismic creep near the town of Ismetpasa using radar data acquired in a single line‐of‐sight direction, requiring several modeling assumptions. We have measured interseismic deformation across the NAF using both ascending and descending data from the Envisat satellite mission acquired between 2003 and 2010. Rather than rejecting incorrectly unwrapped areas in the interferograms, we develop a new iterative unwrapping procedure for small baseline interferometric synthetic aperture radar (InSAR) processing that expands the spatial coverage. Our method corrects unwrapping errors iteratively and increases the robustness of the unwrapping procedure. We remove long wavelength trends from the InSAR data using GNSS observations and deconvolve the InSAR velocities into fault‐parallel motion. Profiles of fault‐parallel velocity reveal a systematic eastward decrease in fault slip rate from 30 mm/yr (25–34, 95% confidence interval (CI)) to 21 mm/yr (14–27, 95% CI) over a distance of ∼200 km. Direct offset measurements across the fault reveal fault creep along a ∼130 km section of the central NAF, with an average creep rate of 8 ± 2 mm/yr and a maximum creep rate of 14 ± 2 mm/yr located ∼30 km east of Ismetpasa. As fault creep is releasing only 30–40% of the long‐term strain in the shallow crust, the fault is still capable of producing large, damaging earthquakes in this region.