A. Ph. Eshanov

A. Ph. Eshanov

Auto-generated profile, based on publicly available information

A. Ph. Eshanov

Kazakh-British Technical University

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 September 2026 in Herald of the Kazakh-British technical university
Verified
Journal Article
Open access
PDF file
MRM. M. Ryskaliyeva
M. M. Ryskaliyeva
AKA. Z. Kusainova
A. Z. Kusainova
AEA. Eshanov
A. Eshanov
IZI. V. Zhirkov
I. V. Zhirkov
AJAkhadov Zamirovich Jobir
Akhadov Zamirovich Jobir
АСА. Т. Султанов
А. Т. Султанов
This study investigates the influence of spin-coated phosphosilicate glass (PSG) on the crystallization and electrical properties of silicon (Si) thin films deposited by magnetron sputtering, with a focus on optimizing their structural and electrical properties for potential applications in photovoltaics and microelectronics. The results demonstrate that higher spin-coating speeds lead to thinner and more uniform PSG layers, which in turn promote more efficient phosphorus diffusion and enhance film crystallization. Annealing at 950 °C resulted in enhanced dopant activation, improved crystallinity, and reduced sheet resistance. These structural and phase transformations were systematically analyzed by X-ray diffraction (XRD), providing detailed insight into the evolution of the Si thin films during thermal processing. In particular, the XRD results reveal a clear transition from the amorphous to the polycrystalline state, especially for samples processed at optimized spin speeds and elevated annealing temperatures. Optical characterization further showed that thermal annealing modified the reflectance and transmittance spectra and slightly increased the refractive index and extinction coefficient of the sputtered Si films. Overall, the combination of environmentally friendly spin-on doping with scalable physical deposition techniques represents a promising approach for the development of advanced photovoltaic technologies, offering a viable pathway toward sustainable and efficient device fabrication.

3 October 2024 in Herald of the Kazakh-British technical university
Verified
Journal Article
Open access
PDF file
KSKeiinbay Symaiyl
Keiinbay Symaiyl
KNK. Kh. Nussupov
K. Kh. Nussupov
ASA. T. Sultanov
A. T. Sultanov
ITIda Tyschenko
Ida Tyschenko
AEA. Ph. Eshanov
A. Ph. Eshanov
СКС. Кейінбай
С. Кейінбай
The films of titanium nitride were deposited by direct current magnetron sputtering on the surface of singlecrystalline silicon samples in an Ar-N2 atmosphere for use as a diffusion barrier. The thickness and density of films were measured by X-ray reflectometry. The design of the MAGNA TM-200-01 installation has been changed to increase the supply of nitrogen into the chamber. The influences of sputtering conditions, including the flow rate of nitrogen and argon gases and their N2 /Ar ratios in the range of 1–60 in the chamber, magnetron power of 690–1400 W on the formation of TiNx films, their density and stoichiometric composition, were studied. It is shown that the value of x is affected not only by the N2 /Ar gas flow rate ratio, but also by the magnetron power. At the sputtering parameters 1200 W, N2 /Ar = 30, 0.8 Pa, 320 s and 100°C, a maximum density of 5.247 g/cm3 of a film was achieved, which corresponds to the composition TiN0.786 = Ti56N44. The presence of nanocrystalline film of titanium nitride and the absence of a nanocrystalline titanium phase were confirmed by photographic X-ray diffraction. It was found that for the synthesis of titanium nitride as close as possible to the stoichiometric composition TiN0.770 - TiN0.786, it is necessary to use magnetron power in the range of 900–1200 W, nitrogen rate of 30 cm3 /min with low argon flows of 1–5 cm3 /min.