Navid Hadifar

Navid Hadifar

Auto-generated profile, based on publicly available information

Navid Hadifar

Department of Electrical Engineering University of South Carolina Columbia South Carolina USA

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 May 2024 in IEEE Open Journal of the Industrial Electronics Society
Verified
Journal Article
Open access
ASAtaollah Samadian
Ataollah Samadian
MMMilad Ghavipanjeh Marangalu
Milad Ghavipanjeh Marangalu
ITIman Talebian
Iman Talebian
NHNavid Hadifar
Navid Hadifar
SHSeyed Hossein Hosseini
Seyed Hossein Hosseini
Hani VahediHani Vahedi
Hani Vahedi
This paper presents a new high step-up Quasi Z-source-based DC-DC converter with switched boost techniques and voltage multiplier cells. Compared to the conventional Z-Source-based converters, this converter, not only can achieve High voltage gain but also, has good efficiency at high output voltage and higher output power conditions. Most of the Z-source-based converters suffer from high current stress across the power MOSFETs and the operation in lower power. However, the other important advantages include very low input current ripple, low voltage and current stress across the power switches, no duty ratio limitation, and leakage current elimination by providing the common grounded feature. So, in this topology, the null of the output is connected to the negative terminal of the input DC source, directly. therefore, the leakage current can be eliminated completely. As a result, the proposed converter is suitable for renewable energy sources (RES) applications such as photovoltaic (PV) systems. The mathematical analysis, operating principle for the proposed converter, and comparison with other converters are evaluated. Finally, in order to verify the accurate performance of the proposed converter and confirm the mentioned features of the proposed converter, a 1 kW laboratory prototype is built and tested

1 January 2026 in IET Circuits, Devices & Systems
Verified
Journal Article
Open access
FSFarzad Mohammadzadeh Shahir
Farzad Mohammadzadeh Shahir
NHNavid Hadifar
Navid Hadifar
This article presents a novel hybrid coupled‐inductor (CI) cascaded high step‐up (HCICHSU) DC–DC converter tailored for renewable energy systems. The proposed converter achieves ultrahigh voltage gain, low voltage stress on semiconductor devices, and continuous input current by combining buck–boost and boost topologies within a hybrid cascaded structure. The topology targets large conversion at a moderate duty cycle while keeping device stresses low and maintaining a smooth input current. Continuous‐conduction operation is analyzed, and expressions for voltage gain, device stresses, and component sizing are derived. A loss model and sensitivity discussion identify dominant loss mechanisms at high conversion ratios. For control, a small‐signal model is developed, and the inherent right‐half‐plane zero (RHPZ) is handled using a Type‐III compensator. Experimental verification uses a 160 W prototype stepping 24 to 200 V. The converter reaches 94.4% efficiency at full load and limits drain‐to‐source peak voltages to about 48 and 60 V for the two main switches, confirming effective leakage‐energy recovery and stress reduction in practice. Measured waveforms show stable regulation and consistent currents.

1 January 2026 in The Journal of Engineering
Verified
Journal Article
Open access
NHNavid Hadifar
Navid Hadifar
FSFarzad Mohammadzadeh Shahir
Farzad Mohammadzadeh Shahir
AHAmir Hadifar
Amir Hadifar
TATouhid Poursheykh Aliasghari
Touhid Poursheykh Aliasghari
HEHamed Eivazi
Hamed Eivazi
In this paper, a new soft‐switching structure for a buck‐boost converter based on pulse width modulation (PWM) is proposed. The proposed structure introduces a simplified soft‐switching approach for buck‐boost converters that achieve zero voltage switching (ZVS) for main switches using only a single auxiliary switch composed of minimal components. Unlike conventional methods that require complex snubber networks or multiple auxiliary elements, the proposed design ensures ZVS‐ZCS operation for all semiconductor elements, significantly reducing switching and reverse recovery losses. Furthermore, its ground‐referenced input and output facilitate practical implementation and system integration. The theoretical analysis is done for the proposed converter during this paper, and its voltage gain is calculated. Also, its duty cycle and switching conditions under zero voltage are determined. Then, design considerations are presented for the proposed converter. Finally, the extensive hardware‐in‐the‐loop (HiL) simulations are carried out for the studied converter to validate the usefulness of the proposed approach under various load conditions. Moreover, experimental results obtained from a laboratory prototype are presented to further validate the theoretical and simulation findings. The prototype achieves an output voltage of 16.5 V and peak efficiency of 97.4% at full load.