A series of dichalcogenophosphinato [Ag(Se2PiPr2)] (1), [Ag(SSePiPr2)]4 (2), and imidodichalcogenodiphosphinatosilver(I) [Ag{iPr2P(S)NP(Se)iPr2}]3 (3) [Ag{(SePiPr2)2N}]3 (4) complexes were synthesised; (2) and (3) were characterised by X-ray single crystallography. Complex (2) has a tetrahedral arrangement of four silver atoms with four thioselenophosphinate ligands along the edges, (3) is a trimer. The compounds (1), (2), (3) and (4) were employed as single-source precursors (SSPs) in aerosol assisted chemical vapour deposition (AACVD) and low pressure (LP) CVD. All precursors gave silver selenide (Ag2Se) films by AACVD, whereas only (3) and (4) deposited Ag2Se films by LPCVD. The as-obtained films were characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX) methods.
The synthesis of the Li-ion conversion candidates, FeF2 and CoF2, obtained from the single source organometallic precursors [Fe(tta)3] (tta = C8H4F3O2S), and [Co(hfac)2·2H2O] (hfac = C5H1F6O2), respectively, via a novel supercritical fluid (SCF) method is presented. The nature of the synthesis led to highly-crystalline FeF2 and CoF2 powders requiring no additional thermal treatment. The as-obtained powders were investigated for use as potential positive Li-ion conversion electrodes by means of chronopotentiometric measurements. The FeF2 cells displayed high initial capacities following electrochemical conversion (up to ∼1100 mA h g−1 at a potential of 1.0 V vs. Li/Li+), with appreciable cyclic behaviour over 25 discharge–charge cycles. The deposition of a ∼5 nm layer of amorphous carbon onto the surface of the active material following SCF treatment, likely facilitated adequate electron transport through an otherwise poorly conducting FeF2 phase. Similarly, CoF2 cells displayed high initial capacities (up to ∼650 mA h g−1 at a potential of 1.2 V vs. Li/Li+), although significant capacity fading ensued in the subsequent cycles. Ex situ XRD measurements confirmed a poor reversibility in the conversion sequence for CoF2, with a complete loss of CoF2 crystallinity and the sole presence of a crystalline LiF phase following charging.
The complexes [Ni{(SePiPr2)2N}2] (1), [Ni(Se2PiPr2)2] (2), and [Co(Se2PiPr2)2] (4) were synthesised and the X-ray single crystal structures of (1) and (2) were determined. Thin films of nickel selenide, cobalt selenide and cobalt phosphide have been deposited by the chemical vapour deposition method using imidodiselenophosphinato-nickel(II) (1), -cobalt(II) [Co{(SePiPr2)2N}2] (3), diselenophosphinato-nickel(II) (2), -cobalt(II) (4) and diselenocarbamato-nickel(II) [Ni(Se2CNEt2)2] (5), and -cobalt(III) [Co(Se2CNEt2)3] (6) precursors.
Reactions of Na(tmeda)[N(iPr2PTe)2] with CuCl, AgI or AuCl (in the presence of PPh3) in THF produced the coinage metal ditelluroimidodiphosphinate complexes {Cu[N(iPr2PTe)2]}3, (5), {Ag[N(iPr2PTe)2]}6 (6) and Au(PPh3)[N(iPr2PTe)2] (7), respectively. Complexes 5, 6 and 7 were characterized in the solid state by X-ray crystallography. Complex 5 is trimeric and exhibits a highly distorted Cu3Te3 ring. In contrast, the Ag(I) complex 6 is a hexamer, and forms a twelve-membered Ag6Te6 ring. The replacement of the iPr groups on phosphorus by Ph results in an intriguing structural change to a tetramer with a boat-shaped Ag4Te4 ring in {Ag[N(Ph2PTe)2}4·2THF (8). The gold(I) complex 7 is monomeric. Aerosol-assisted chemical vapour deposition (AACVD) of compounds 5, 6 and 7 yields CuTe, Ag7Te4, AuTe2 and Au films, respectively. The films were grown at temperatures of 300–500 °C and characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive analysis of X-rays (EDAX).