The Materials Node of the Australian National Nanofabrication Facility, Intelligent Polymer Research Institute University of Wollongong Wollongong New South Wales Australia
Auto-generated profile, based on publicly available information
Sepidar Sayyar
The Materials Node of the Australian National Nanofabrication Facility, Intelligent Polymer Research Institute University of Wollongong Wollongong New South Wales Australia
Processable graphene/polycaprolactone composites for tissue engineering were produced in a simultaneous one-step polymerisation/reduction process without toxic reducing agents.
Piezoelectric fibers have an important role in wearable technology as energy generators and sensors. A series of hybrid nanocomposite piezoelectric fibers of polyinylidene fluoride (PVDF) loaded with barium–titanium oxide (BT) and reduced graphene oxide (rGO) were prepared via the melt spinning method. Our previous studies show that high-performance fibers with 84% of the electroactive β-phase in the PVDF generated a peak output voltage up to 1.3 V and a power density of 3 W kg−1. Herein, the dynamic mechanical and creep behavior of these fibers were investigated to evaluate their durability and piezoelectric performance. Dynamic mechanical analysis (DMA) was used to provide phenomenological information regarding the viscoelastic properties of the fibers in the longitudinal direction. DSC and SEM were employed to characterize the crystalline structure of the samples. The storage modulus and the loss tangent increased by increasing the frequency over the temperature range (−50 to 150 °C) for all of the fibers. The storage modulus of the PVDF/rGO nanocomposite fibers had a higher value (7.5 GPa) in comparison with other fibers. The creep and creep recovery behavior of the PVDF/nanofillers in the nanocomposite fibers have been explored in the linear viscoelastic region at three different temperatures (10–130 °C). In the PVDF/rGO nanocomposite fibers, strong sheet/matrix interfacial interaction restricted the mobility of the polymer chains, which led to a higher modulus at temperatures 60 and 130 °C.
Melt-electrowriting (MEW) is an emerging method that combines electrospinning and extrusion printing, allowing the fabrication of micron-scale structures suitable for tissue engineering. Compared to other additive fabrication methods, melt-electro written structures can offer more appropriate substrates for cell culture due to filament size and mechanical characteristics of the fabricated scaffolds. In this study, polycaprolactone (PCL)/graphene composites were investigated for fabrication of micron-size scaffolds through MEW. It was demonstrated that the addition of graphene can considerably improve the processability of PCL to fabricate micron-scale scaffolds with enhanced resolution. The tensile strength of the scaffold prepared from PCL/graphene composite (with only 0.5 wt.% graphene) was proved significantly (by more than 270%), better than that of the pristine PCL scaffold. Furthermore, graphene was demonstrated to be a suitable material for tailoring the degradation process to avoid undesirable bulk degradation, rapid mass loss and damage to the internal matrix of the polymer. The findings of this study offer a promising route for the fabrication of high-resolution scaffolds with micron-scale resolution for tissue engineering.
18 October 2020 in Journal of Biomedical Materials Research Part B: Applied Biomaterials
In this work fibres and complex three-dimensional scaffolds of a covalently linked graphene-polycaprolactone composite were successfully extruded and printed using a melt extrusion printing system. Fibres with varying diameters and morphologies, as well as complex scaffolds were fabricated using an additive fabrication approach and were characterized. It was found that the addition of graphene improves the mechanical properties of the fibres by over 50% and in vitro cytotoxicity tests showed good biocompatibility indicating a promising material for tissue engineering applications.
This work represents an environmentally sound method to form graphene through ball-milling expanded graphite in the presence of the vitamin B2 derivative Riboflavin Mononucleotide to give a covalently bonded, highly dispersible, low defect graphene.